Nissan Primera P12. Manual — part 716
WW-48
REAR WIPER AND WASHER SYSTEM
REMOVAL (WAGON)
1.
Remove the back door finisher. Refer to EI section in P12 ESM (SM2E00-1P12E0E).
2.
Operate the wiper motor, and stop it at the auto stop position.
3.
Disconnect wiper motor connector.
4.
Remove wiper arm from the vehicle.
5.
Remove wiper motor form the vehicle.
6.
Remove rubber from the vehicle.
REMOVAL (HATCH BACK)
1.
Remove the back door finisher. Refer to EI section in P12 ESM (SM2E00-1P12E0E).
2.
Operate the wiper motor, and stop it at the auto stop position.
3.
Disconnect wiper motor connector.
4.
Remove wiper arm from the vehicle.
5.
Remove wiper motor form the vehicle.
6.
Remove rubber from the vehicle.
INSTALLATION
1.
Install rubber to the vehicle.
2.
Install wiper motor to the vehicle.
3.
Connect wiper motor to connector. Turn the wiper switch ON to operate wiper motor, then turn the wiper
switch OFF (auto stop).
4.
Install wiper arm to the vehicle.
5.
Install back door finisher. Refer to EI section in P12 ESM (SM2E00-1P12E0E).
●
Tighten windshield wiper arm nuts to specified torque.
●
Tighten windshield wiper motor nuts to specified torque.
CAUTION:
●
Do not drop the wiper motor or cause it to contact other parts.
●
Check the grease conditions of the motor arm and wiper link joint (at retainer). Apply grease if
necessary.
SKIA0274E
MKIB0240E
: 12.7 - 17.6 N-m (1.3 - 1.8 kg-m, 10 - 13 ft-lb)
: 3.8 - 5.1 N-m (0.39 - 0.52 kg-m, 34 - 45 in-lb)
REAR WIPER AND WASHER SYSTEM
WW-49
C
D
E
F
G
H
I
J
L
M
A
B
WW
Washer Nozzle Adjustment
EKS009PO
●
Adjust washer nozzle with suitable tool as shown in the figure at right.
(WAGON)
Unit: mm (in)
*: The diameter of this circle is less than 30 mm (1.18 in).
(HATCH BACK)
Unit: mm (in)
Removal and Installation for Rear Washer Nozzle
EKS009PP
REMOVAL (WAGON)
1.
Remove washer hose from washer nozzle.
2.
Remove washer nozzle installation nut and remove washer noz-
zle.
Adjustable range
:
±
15
°
(In any direction)
MKIA0031E
*H
113 (4.45)
* L
22.7 (0.894)
MKIA0032E
H1
16 (0.63)
H2
20 (0.79)
L1
65 (2.56)
L2
69 (2.72)
MKIB0241E
SKIA0275E
WW-50
REAR WIPER AND WASHER SYSTEM
REMOVAL (HATCH BACK)
1.
Push washer nozzle pawl toward to pullout.
NOTE:
When removing or installing the washer nozzle, carefully handle it to keep avoid damage.
2.
Remove washer hose from washer nozzle.
INSTALLATION
1.
Installation is in the reverse order of removal.
2.
Adjust nozzle injection position.
Inspection for Washer Nozzle
EKS009PQ
CHECK VALVE
●
Blow air in the injection direction, and check that air flows only
one way. Make sure that the reverse direction (inhale) is not
possible.
Removal and Installation for Wiper and Washer Switch
EKS009PR
Refer to
WW-16, "Removal and Installation for Wiper and Washer Switch"
.
Removal and Installation for Washer Tank
EKS009PS
Refer to
WW-16, "Removal and Installation for Washer Tank"
.
Removal and Installation for Washer Pump
EKS009PT
Refer to
WW-16, "Removal and Installation for Washer Pump"
.
MKIB0242E
MKIA0033E
REAR WIPER AND WASHER SYSTEM
WW-51
C
D
E
F
G
H
I
J
L
M
A
B
WW
Washer Tube Layout
EKS009PU
(WAGON)
(HATCH BACK)
MKIA0043E
MKIB0243E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст