Nissan Primera P12. Manual — part 330
DTC P0336 CKP SENSOR
EC-505
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
5.
Check resistance as shown in the figure.
6.
If NG, replace crankshaft position sensor.
Removal and Installation
EBS0157F
CRANKSHAFT POSITION SENSOR
Refer to
EM-29, "OIL PAN AND OIL STRAINER"
.
Terminal No. (Polarity)
Resistance
Ω
[at 25
°
C (77
°
F)]
1 (+) - 2 (-)
Except 0
1 (+) - 3 (-)
Except 0 or
∞
2 (+) - 3 (-)
Except 0
MBIB1009E
EC-506
[YD (WITHOUT EURO-OBD)]
DTC P0340 CMP SENSOR
DTC P0340 CMP SENSOR
PFP:23731
Description
EBS0157G
The camshaft position sensor identifies a particular cylinder by
means of signals from the sensing plate (with five protrusions)
installed to the camshaft. The datum signal output is detected 90
°
signal and sent to the ECM.
ECM Terminals and Reference Value
EBS0157H
Specification data are reference values and are measured between each terminal and ground.
Pulse signal is measured by CONSULT-II.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
On Board Diagnosis Logic
EBS0157I
MBIB0618E
TERMI-
NAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA
(DC Voltage and Pulse Signal)
45
R
Camshaft position sensor
power supply
[Ignition switch ON]
Approximately 5.3V
47
B
Camshaft position sensor
[Engine is running]
●
Warm-up condition
●
Idle speed
0 - 6V
[Engine is running]
●
Warm-up condition
●
Engine speed is 2,000 rpm
0 - 6V
66
W
Camshaft position sensor
ground
[Ignition switch ON]
Approximately 0.3V
67
—
Sensor ground
(Sensors shield circuit)
[Ignition switch ON]
Approximately 0.3V
MBIB0877E
MBIB0878E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0340
Camshaft position sensor
circuit
Camshaft position sensor signal is not detect by
the ECM when engine is running.
●
Harness or connectors
(The sensor circuit is open or
shorted.)
●
Camshaft position sensor
DTC P0340 CMP SENSOR
EC-507
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC Confirmation Procedure
EBS0157J
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Start engine and let it idle for at least 5 seconds.
If engine could not start, keep ignition switch at START position
for 5 seconds.
4.
If DTC is detected, go to
EC-509, "Diagnostic Procedure"
.
SEF817Y
EC-508
[YD (WITHOUT EURO-OBD)]
DTC P0340 CMP SENSOR
Wiring Diagram
EBS0157K
MBWA0380E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст