Nissan Primera P12. Manual — part 622
MA-30
CHASSIS AND BODY MAINTENANCE
CHASSIS AND BODY MAINTENANCE
PFP:00100
Checking Exhaust System
ELS000OY
Check exhaust pipes, muffler and mounting for improper attachment,
leaks, cracks, damage, chafing or deterioration.
Checking Clutch Fluid Level and Leaks
ELS000OZ
If fluid level is extremely low, check clutch system for leaks.
Checking Clutch System
ELS000P0
Check fluid lines and operating cylinder for improper attachment,
cracks, damage, loose connections, chafing and deterioration.
Checking M/T Oil
ELS000P1
●
Check that oil is not leaking from transaxle or around it.
●
Check oil level from filler plug mounting hole as shown in the fig-
ure.
CAUTION:
Never start engine while checking oil level.
●
Set a new gasket on the filler plug and install it on the transaxle.
CAUTION:
Do not reuse gasket.
SMA211A
SFIA0066J
SMA859
Filler plug:
RS6F93R
: 35 N·m (3.6 kg-m, 26 ft-lb)
RS6F51R
: 30 - 39 N·m (3.1 - 4.0 kg-m, 23 - 28 ft-lb)
SMA066C
CHASSIS AND BODY MAINTENANCE
MA-31
C
D
E
F
G
H
I
J
K
M
A
B
MA
Changing M/T Oil
ELS000P2
1.
Drain oil from drain plug and refill with new gear oil.
2.
Check oil level.
CAUTION:
Do not reuse gasket.
Balancing Wheels
ELS000P7
Adjust wheel balance using the road wheel center.
Rotation
ELS000P8
●
After rotating the tires, adjust the tire pressure.
●
Retighten the wheel nuts when the vehicle has been driven for
1,000 km (600 miles) (also in cases of a flat tire, etc.).
CAUTION:
When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.
Checking Brake Fluid Level and Leaks
ELS000P9
●
If fluid level is extremely low, check brake system for leaks.
Oil grade and viscosity:
Refer to
MA-15, "RECOMMENDED FLUIDS AND LUBRICANTS"
Oil capacity (Reference):
RS6F93R
Approx. 2.1
(1-7/8 lmp qt)
RS6F51R
Approx. 2.3
(2 lmp qt)
Drain plug:
RS6F93R
: 35 N·m (3.6 kg-m, 26 ft-lb)
RS6F51R
: 30 - 39 N·m (3.1 - 4.0 kg-m, 23 - 28 ft-lb)
Wheel balance (Maximum allowable unbalance):
Refer to
.
Tightening torque of wheel nut:
98 - 118N·m (10 - 12 kg·m, 72 - 87 ft·lb)
SMA829C
SFIA0066J
MA-32
CHASSIS AND BODY MAINTENANCE
Checking Brake Lines and Cables
ELS000PA
●
Check brake fluid lines and parking brake cables for improper
attachment, leaks, chafing, abrasions, deterioration, etc.
Changing Brake Fluid
ELS000PB
1.
Drain brake fluid from each air bleeder valve.
2.
Refill until new brake fluid comes out from each air bleeder
valve.
Use same procedure as in bleeding hydraulic system to refill
brake fluid.
Refer to
.
●
Refill with recommended Genuine Brake Fluid or equivalent
“DOT 3” or “DO4”.
Refer to
MA-15, "RECOMMENDED FLUIDS AND LUBRI-
.
●
Never reuse drained brake fluid.
●
Be careful not to splash brake fluid on painted areas.
Checking Disc Brake
ELS000PC
ROTOR
Check condition, wear, and damage.
CALIPER
●
Check for leakage.
SBR389C
SBR419C
Applied
Front
Rear
Brake model
CL25VCG
FNc38/11/11, FN11
Standard thickness
28.0 mm (1.102 in)
10.0 mm (0.39 in)
Maximum runout
0.07 mm (0.0028 in)
0.15 mm (0.0059 in)
Minimum thickness (Wear limit)
26.0 mm (1.024 in)
9.0 mm (0.35 in)
SMA922A
CHASSIS AND BODY MAINTENANCE
MA-33
C
D
E
F
G
H
I
J
K
M
A
B
MA
PAD
●
Check for wear or damage.
Checking Steering Gear and Linkage
ELS000PD
STEERING GEAR
●
Check gear housing and boots for looseness, damage and
grease leakage.
●
Check connection with steering column for looseness.
STEERING LINKAGE
Check ball joint, dust cover and other component parts for looseness, wear, damage and grease leakage.
Checking Power Steering Fluid and Lines
ELS000PE
Check fluid level in reservoir tank with engine off.
Use “HOT” range at fluid temperatures of 50 to 80
°
C (122 to 176
°
F)
or “COLD” range at fluid temperatures of 0 to 30
°
C (32 to 86
°
F).
CAUTION:
●
Do not overfill.
●
Recommended fluid is DEXRON
TM
III or equivalent.
Refer to
MA-15, "RECOMMENDED FLUIDS AND LUBRI-
BRA0010D
Applied
Front
Rear
Brake model
CL25VCG
FNc38/11/11,FN11
Standard thickness
11.0 mm (0.433 in)
11.0 mm (0.433 in)
Minimum thickness (Wear Limit)
2.0 mm (0.079 in)
2.0 mm (0.079 in)
SLIA0014E
SST850C
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст