Nissan Altima HL32 Hybrid. Manual — part 250
![](/vehicles/gon/sttello/nita/jeee.png)
DOOR
DLK-221
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT DOOR : Adjustment
INFOID:0000000004215795
1.
Front fender
2.
Front door assembly
3.
Rear door assembly
4.
Center mud guard
5.
Center pillar
6.
Outer sill
AWKIA0450GB
![](/vehicles/gon/sttello/nita/erulala.png)
DLK-222
< ON-VEHICLE REPAIR >
DOOR
Unit: mm (in)
LONGITUDINAL CLEARANCE
1. Confirm the back door adjustments and adjust if necessary. Refer to
2. Remove the front fender. Refer to
DLK-217, "Removal and Installation"
3. Loosen the hinge bolts. Raise or lower the front door at rear edge to adjust.
4. Install the front fender. Refer to
DLK-217, "Removal and Installation"
.
SURFACE HEIGHT ADJUSTMENT
1. Loosen the front door hinge nuts.
2. Move the top and or bottom in or out as necessary until it is
within specifications.
3. Tighten the hinge nuts to specifications.
BACK DOOR
BACK DOOR : Removal and Installation
INFOID:0000000004215796
REMOVAL
CAUTION:
• When removing and installing the rear door assembly, support the door with a jack and cloth to pro-
tect the door and body.
• When removing and installing rear door assembly, be sure to carry out the fitting adjustment.
• Check the hinge rotating parts for poor lubrication. If necessary, apply “body grease”.
• After installing, apply touch-up paint (the body color) onto the head of the hinge nuts.
• Operate with two workers, because of its heavy weight.
• Check rear door open/close operation after installation.
Section
Item
Measurement
Standard
A-A
F
Clearance
4.5
± 1.5 (0.18 ± 0.06)
G
Surface height
0.0
± 1.5 (0.0 ± 0.06)
B-B
H
Clearance
4.2
± 1.0 (0.17 ± 0.04)
J
Surface height
0.0
± 1.0 (0.0 ± 0.04)
C-C
K
Clearance
4.2
± 1.0 (0.17 ± 0.04)
M
Surface height
0.0
± 1.0 (0.0 ± 0.04)
D-D
N
Clearance
5.1
± 1.7 (0.20 ± 0.07)
E-E
P
Clearance
3.6
± 1.0 (0.14 ± 0.04)
Q
Surface height
0.0
± 1.0 (0.0 ± 0.04)
ALKIA0016GB
![](/vehicles/gon/sttello/nita/lleideca.png)
DOOR
DLK-223
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1. Pull out grommet and disconnect rear door harness connector.
2. Remove the check link bolt from the center pillar.
3. Remove the door-side hinge nuts (a) and the door assembly (1).
INSTALLATION
Installation is in the reverse order of removal.
REAR DOOR: ADJUSTMENT
ALKIA0016GB
![](/vehicles/gon/sttello/nita/llacruell.png)
DLK-224
< ON-VEHICLE REPAIR >
DOOR
Unit: mm (in)
1.
Rear door assembly
2.
Center mud guard
3.
Body side outer
Section
Item
Measurement
Standard
A-A
D
Clearance
3.6
± 1.0 (0.14 ± 0.04)
E
Surface height
0.0
± 1.0 (0.0 ± 0.04)
AWKIA0451GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст