Nissan Altima HL32 Hybrid. Manual — part 406
![](/vehicles/gon/sttello/nita/biguerreenth.png)
EXL-24
< FUNCTION DIAGNOSIS >
COMBINATION SWITCH
Wiper intermittent dial posi-
tion
Intermittent oper-
ation delay inter-
val
INT VOLUME switch ON/OFF status
INT VOLUME 1 switch
INT VOLUME 2 switch
INT VOLUME 3 switch
1
Short
↑
↓
Long
ON
ON
ON
2
ON
ON
OFF
3
ON
OFF
OFF
4
OFF
OFF
OFF
5
OFF
OFF
ON
6
OFF
ON
ON
7
OFF
ON
OFF
![](/vehicles/gon/sttello/nita/onen.png)
DIAGNOSIS SYSTEM (BCM)
EXL-25
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : Diagnosis Description
INFOID:0000000004501352
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000004501353
ECU IDENTIFICATION
Displays the BCM part No.
SELF-DIAG RESULT
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function.
SELF-DIAG RESULTS
Displays the diagnosis results judged by BCM.
CAN DIAG SUPPORT MNTR
Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
ECU IDENTIFICATION
The BCM part number is displayed.
CONFIGURATION
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
WORK SUPPORT
DATA MONITOR
ACTIVE TEST
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps FLASHER
×
×
×
Air conditioner
AIR CONDITONER
×
Intelligent Key system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
BCM
BCM
×
Immobilizer
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Trunk open
TRUNK
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
AIR PRESSURE MONITOR
×
×
×
![](/vehicles/gon/sttello/nita/qunathlutrui.png)
EXL-26
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)
INFOID:0000000004501355
WORK SUPPORT
1 : Initial setting
2 : With auto light system
DATA MONITOR
Work item
Setting item
Setting
BATTERY SAVER SET
ON
1
With the exterior lamp battery saver function
OFF
Without the exterior lamp battery saver function
ILL DELAY SET
2
MODE 1
1
45 sec.
Sets delay timer function timer operation time
(All doors closed)
MODE 2
Without the func-
tion
MODE 3
30 sec.
MODE 4
60 sec.
MODE 5
90 sec.
MODE 6
120 sec.
MODE 7
150 sec.
MODE 8
180 sec.
CUSTOM A/LIGHT
SETTING
2
MODE 1
1
Normal
MODE 2
More sensitive setting than normal setting (Turns ON earlier than normal operation.)
MODE 3
More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)
MODE 4
Less sensitive setting than normal setting (Turns ON later than normal operation.)
Monitor item
[Unit]
Description
PUSH SW
[ON/OFF]
The switch status input from push-button ignition switch
ENGINE STATE
[STOP/STALL/CRANK/RUN]
The engine status received from ECM with CAN communication
VEH SPEED 1
[km/h]
The value of the vehicle speed received from combination meter with CAN commu-
nication
KEY SW-SLOT
[ON/OFF]
Key switch status input from key slot
![](/vehicles/gon/sttello/nita/lache.png)
DIAGNOSIS SYSTEM (BCM)
EXL-27
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
1: The item is indicated, not monitored
2: With auto light system
ACTIVE TEST
TURN SIGNAL R
[ON/OFF]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[ON/OFF]
TAIL LAMP SW
[ON/OFF]
HI BEAM SW
[ON/OFF]
HEAD LAMP SW1
[ON/OFF]
HEAD LAMP SW2
[ON/OFF]
PASSING SW
[ON/OFF]
AUTO LIGHT SW
[ON/OFF]
FR FOG SW
[ON/OFF]
DOOR SW-DR
[ON/OFF]
The switch status input from front door switch LH
DOOR SW-AS
[ON/OFF]
The switch status input from front door switch RH
DOOR SW-RR
[ON/OFF]
The switch status input from rear door switch RH
DOOR SW- RL
[ON/OFF]
The switch status input from rear door switch LH
DOOR SW-BK
1
[ON/OFF]
—
OPTICAL (LIGHT) SENSOR
[V]
2
The value of exterior brightness voltage input from the optical sensor
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
ON
Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.
OFF
Stops the tail lamp request signal transmission.
HEAD LAMP
HI
Transmits the high beam request signal with CAN communication to turn
the headlamp (HI)
LO
Transmits the low beam request signal with CAN communication to turn
the headlamp (LO).
OFF
Stops the high & low beam request signal transmission.
FR FOG LAMP
ON
Transmits the front fog lamp light request signal to IPDM E/R with CAN
communication to turn the front fog lamp ON.
OFF
Stops the front fog lamp request signal transmission.
DAYTIME RUNNING LIGHT
1
ON
Transmits the daytime running light system request signal to IPDM E/R
OFF
Stops the daytime running light request signal transmission
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст