Nissan Altima HL32 Hybrid. Manual — part 108
![](/vehicles/gon/sttello/nita/jene.png)
REAR DISC BRAKE
BR-43
< DISASSEMBLY AND ASSEMBLY >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
2. Place a wooden block in the caliper as shown, and blow air into
the union bolt hole to the remove piston and piston boot.
CAUTION:
Do not get fingers caught between the piston and wooden
block.
3. Remove the piston seal from the caliper using a suitable tool.
Discard the piston seal.
CAUTION:
• Be careful not to damage a cylinder inner wall.
• Do not reuse the piston seal.
BRAKE CALIPER ASSEMBLY : Inspection After Disassembly
INFOID:0000000004212589
CALIPER
Check the inner wall of the cylinder for corrosion, wear, and damage. Replace as necessary.
CAUTION:
Clean the caliper using new brake fluid. Never use mineral oils such as gasoline or kerosene.
TORQUE MEMBER
Check the torque member for wear, cracks, and damage. Replace as necessary.
PISTON
Check the piston surface for corrosion, wear, and damage. Replace as necessary.
CAUTION:
The piston sliding surface is plated. Do not polish with sandpaper.
SLIDING PIN BOLT, SLIDING PIN BOOT
Check the sliding pin bolt and sliding pin boot for wear, damage, and cracks. Replace as necessary.
BRAKE CALIPER ASSEMBLY : Assembly
INFOID:0000000004212588
ASSEMBLY
CAUTION:
Use NISSAN Rubber Grease during assembly.
1. Apply rubber grease to new piston seal, and install them on cali-
per.
CAUTION:
Do not reuse piston seal.
BRD0041D
SFIA2277E
SFIA2278E
![](/vehicles/gon/sttello/nita/othe.png)
BR-44
< DISASSEMBLY AND ASSEMBLY >
REAR DISC BRAKE
2. Apply rubber grease to new piston boot. Cover the piston end
with the new piston boot, and then install cylinder side lip on the
new piston boot securely into the groove on caliper.
CAUTION:
Do not reuse piston boot.
3. Push piston into caliper by hand and push piston boot piston
side lip into the piston groove.
CAUTION:
Press the piston evenly and vary the pressing point to pre-
vent cylinder inner wall from being rubbed.
4. Secure piston boot with new retaining ring.
CAUTION:
• Make sure that boot is securely engaged in the groove on
caliper.
• Do not reuse retainer ring.
SFIA2498E
SFIA2279E
SFIA2280E
![](/vehicles/gon/sttello/nita/velle.png)
SERVICE DATA AND SPECIFICATIONS (SDS)
BR-45
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specifications
INFOID:0000000004212590
Unit: mm (in)
Brake Pedal
INFOID:0000000004212591
Front Disc Brake
INFOID:0000000004212592
Front brake
Cylinder bore diameter (each)
57.2 (2.25)
Pad length
× width × thickness
126.5
× 52 × 11 (4.98 × 2.047 × 0.433)
Rotor outer diameter
× thickness
296
× 26 (11.65 × 1.024)
Rear brake
Cylinder bore diameter
34.93 (1.375)
Pad length
× width × thickness
83
× 33 × 8.5 (3.268 × 1.299 × 0.335)
Rotor outer diameter
× thickness
292
× 9 (11.50 × 0.354)
Recommended brake fluid
DOT 3
H
Brake pedal height (from dash lower panel top surface)
191.7 - 205.7 mm (7.55 - 8.10 in)
S
Brake pedal full stroke
[under a force of 490 N (50 kg-f, 110 lb-f) with engine running]
130 mm (5.12 in)
C
1
,
C
2
Clearance between bracket and threaded end of the stop lamp switch and ASCD
cancel switch
0.74 - 1.96 mm (0.0291 - 0.0772 in)
AWFIA0433ZZ
Brake pad
Standard thickness (new)
11.0 mm (0.433 in)
Wear limit thickness
2.0 mm (0.079 in)
![](/vehicles/gon/sttello/nita/hongs.png)
BR-46
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Rear Disc Brake
INFOID:0000000004212593
Disc rotor
Standard thickness (new)
26.0 mm (1.024 in)
Wear limit thickness
24.0 mm (0.945 in)
Thickness variation (measured at 8 positions)
0.015 mm (0.0006 in)
Maximum runout (with it attached to the vehicle)
0.040 mm (0.0016 in)
Brake pad
Standard thickness (new)
8.5 mm (0.335 in)
Wear limit thickness
1.0 mm (0.039 in)
Disc rotor
Standard thickness (new)
9.0 mm (0.354 in)
Wear limit thickness
8.0 mm (0.315 in)
Thickness variation (measured at 8 positions)
0.015 mm (0.0006 in)
Maximum runout (with it attached to the vehicle)
0.05 mm (0.0020 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст