Nissan Altima HL32 Hybrid. Manual — part 1052
![](/vehicles/gon/sttello/nita/wher.png)
ST-6
< ON-VEHICLE MAINTENANCE >
STEERING WHEEL
ON-VEHICLE MAINTENANCE
STEERING WHEEL
Inspection
INFOID:0000000004212800
STEERING WHEEL AXIAL END PLAY
• Check installation conditions of steering gear assembly, front suspension assembly, axle and steering col-
umn assembly.
• Check if movement exists when steering wheel is moved up and down, to the left and right and to the axial
direction.
• Check steering gear assembly mounting bolts and nut for looseness. Refer to
.
STEERING WHEEL PLAY
• Turn steering wheel so that front wheels come to the straight-
ahead position. Start engine and lightly turn steering wheel to the
left and right until front wheels start to move. Measure steering
wheel movement on the outer circumference as shown.
• When the measurement value is outside the standard value, check
backlash for each joint of steering column assembly and installa-
tion condition of steering gear assembly.
NEUTRAL POSITION OF STEERING WHEEL
• Make sure that steering gear assembly, steering column assembly and steering wheel are installed in the
correct position.
• Perform neutral position inspection after wheel alignment. Refer to
STEERING ANGLE SENSOR : Special Repair Requirement"
• Set vehicle to the straight-ahead position and confirm steering wheel is in the neutral position.
• Loosen outer socket lock nut and turn inner socket to left and right equally to make fine adjustments if steer-
ing wheel is not in the neutral position.
STEERING WHEEL TURNING FORCE
1. Park vehicle on a level, dry surface and set parking brake.
2. Start engine.
3. Tires need to be inflated to normal pressure.
4. Check steering wheel turning force when steering wheel has
been turned 360
° from the neutral position using Tool.
5. If steering wheel turning force is out of specification, check rack
sliding force. Refer to
.
6. If rack sliding force is not within specifications, adjust rack slid-
ing force. Refer to
7. If rack sliding force is OK, inspect steering column. Refer to
ST-9, "Removal and Installation"
FRONT WHEEL TURNING ANGLE
Steering wheel axial end play : 0 mm (0 in)
Steering wheel play : 0 - 35 mm (0 - 1.38 in)
WGIA0034E
Tool Number
: — (J-44372)
Steering wheel turning force
: 39 N (4 kg-f, 9 lb-f)
or less
WGIA0035E
![](/vehicles/gon/sttello/nita/chondela.png)
STEERING WHEEL
ST-7
< ON-VEHICLE MAINTENANCE >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
• Check front wheel turning angle after toe-in inspection. Place front
wheels on turning radius gauges and rear wheels on stands.
Check the maximum inner and outer wheel turning angles for LH
and RH road wheels.
• With the engine at idle, turn steering wheel from full left stop to full
right stop and measure the turning angles.
Unit: Degree Minute (Decimal Degree)
• Measure rack stroke if angles are outside the specified value.
FAA0016D
SGIA0055E
Inner wheel (Angle: A)
Minimum
35
° 30′ (35.5°)
Nominal
38
° 30′ (38.5°)
Maximum
39
° 30′ (39.5°)
Outer wheel (Angle: B)
Nominal
31
° 30′ (31.5°)
Rack stroke “L”
69 mm (2.72 in)
JSGIA0171GB
![](/vehicles/gon/sttello/nita/ches.png)
ST-8
< ON-VEHICLE REPAIR >
STEERING WHEEL
ON-VEHICLE REPAIR
STEERING WHEEL
Removal and Installation
INFOID:0000000004212801
REMOVAL
NOTE:
When reconnecting spiral cable, fix cable with a tape so that fixing case and rotating part keep aligned. This
will omit neutral position alignment procedure during spiral cable installation.
1. Set front wheels to straight-ahead position.
2. Remove driver air bag module. Refer to
SRS-10, "Removal and Installation"
3. Remove steering wheel lock nut and washer after steering column is locked.
4. Remove steering wheel using Tool (A).
INSTALLATION
Installation is in the reverse order of removal.
• As necessary, set the spiral cable neutral position.
- Slowly turn the spiral cable clockwise to the end position.
- Next, turn it counterclockwise (approximately 2 turns) then stop
turning at the point when the alignment arrows (B) are directly
across from each other.
- Rotate the spiral cable slightly so the locating pin (2) is positioned
at the top.
NOTE:
A service part is installed in the neutral position with a stopper clip
in place and should not be adjusted after the stopper clip is
removed.
- Align the locating hole (1) at the top of the steering wheel with the
locating pin (2) of the spiral cable during installation.
- Spiral cable screws (A)
CAUTION:
• The spiral cable may snap by steering operation if the cable is
installed in an improper position.
• Do not turn the spiral cable quickly or beyond the limit num-
ber of turns. (This can cause the cable to snap.)
• After the work is completed, make sure no system malfunc-
tion is detected by air bag warning lamp.
• In case a malfunction is detected by the air bag warning lamp,
reset with the self-diagnosis function and delete the memory
with CONSULT
−III.
• If a malfunction is still detected after the above operation, perform self-diagnosis to repair malfunc-
tions. Refer to
SRC-7, "Driver Air Bag Module"
Tool number A: ST27180001 (J-25726-A)
AWGIA0004GB
Steering wheel lock nut
: 34.3 N·m (3.5 kg-m, 25 ft-lb)
ALHIA0014ZZ
![](/vehicles/gon/sttello/nita/xthin.png)
STEERING COLUMN
ST-9
< ON-VEHICLE REPAIR >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
STEERING COLUMN
Exploded View
INFOID:0000000004212802
Removal and Installation
INFOID:0000000004212803
REMOVAL
1. Set wheels to the straight ahead-position.
2. Remove lower side bolt of lower shaft assembly.
3. Remove upper side bolt of lower shaft, then remove lower shaft assembly from steering gear assembly.
4. Loosen herbie clip, then remove hole cover seal from hole cover.
1-4. Steering column assembly nut
tightening order
5.
Steering wheel
6.
Combination switch and spiral cable
7.
Steering column assembly
8.
Hole cover seal
9.
Herbie clip
10.
Hole cover
11. Lower shaft assembly
AWGIA0067GB
SGIA0844E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст