Nissan Altima HL32 Hybrid. Manual — part 194
PRECAUTIONS
DEF-55
< PRECAUTION >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
PRECAUTION
PRECAUTIONS
Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSION-
ER"
INFOID:0000000004216350
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000004499022
NOTE:
• Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both 12-volt battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both 12-
volt battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the 12-volt battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the 12-volt battery disconnected or discharged, follow the proce-
dure below before starting the repair operation.
OPERATION PROCEDURE
1. Connect both 12-volt battery cables.
NOTE:
Supply power using jumper cables if 12-volt battery is discharged.
2. Carry the Intelligent Key or insert it to the key slot and turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3. Disconnect both 12-volt battery cables. The steering lock will remain released with both 12-volt battery
cables disconnected and the steering wheel can be turned.
4. Perform the necessary repair operation.
5. When the repair work is completed, re-connect both 12-volt battery cables. With the brake pedal released,
turn the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steer-
ing wheel will lock when the push-button ignition switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT-III.
![](/vehicles/gon/sttello/nita/bil.png)
DEF-56
< ON-VEHICLE REPAIR >
FILAMENT
ON-VEHICLE REPAIR
FILAMENT
Inspection and Repair
INFOID:0000000004216351
INSPECTION
1. When measuring voltage, wrap tin foil around the top of the neg-
ative probe. Then press the foil against the wire with your finger.
2. Attach probe circuit tester (in Volt range) to middle portion of
each filament.
3. If a filament is burned out, circuit tester registers 0 or battery
voltage.
4. To locate burned out point, move probe to left and right along fil-
ament. Test needle will swing abruptly when probe passes the
point.
REPAIR
Repair Equipment
• Conductive silver composition (Dupont No. 4817 or equivalent)
SEL122R
SEL263
SEL265
![](/vehicles/gon/sttello/nita/xxu.png)
FILAMENT
DEF-57
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
• Ruler 30 cm (11.8 in) long
• Drawing pen
• Heat gun
• Alcohol
• Cloth
Repairing Procedure
1. Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.
2. Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use.
3. Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
4. After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
composition is deposited.
Do not touch repaired area while test is being conducted.
5. Apply a constant stream of hot air directly to the repaired area
for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet.
If a heat gun is not available, let the repaired area dry for 24
hours.
PIIA0215E
SEL012D
SEL013D
![](/vehicles/gon/sttello/nita/verusoll.png)
DEF-58
< ON-VEHICLE REPAIR >
CONDENSER
CONDENSER
Removal and Installation
INFOID:0000000004216352
REMOVAL
1. Remove the rear seat cushion and the rear seat back.
SE-22, "Removal and Installation"
.
2. Remove the rear kickplate, rear wheel well garnish and the rear pillar finisher.
INT-16, "Removal and Installation"
3. Remove the condenser bolt (A), and then remove the condenser
(1) from the rear pillar.
INSTALLATION
Installation is in the reverse order of removal.
JMLIA0013ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст