Nissan Altima HL32 Hybrid. Manual — part 760
![](/vehicles/gon/sttello/nita/whi.png)
IP-12
< ON-VEHICLE REPAIR >
INSTRUMENT PANEL ASSEMBLY
Removal and Installation
INFOID:0000000004215443
CAUTION:
• Disconnect both the negative and positive 12 volt battery terminals, then wait at least three minutes.
• Never tamper with or force air bag lid open, as this may adversely affect air bag performance.
• Be careful not to scratch instrument panel pad and other parts.
REMOVAL
1. Disconnect the negative and positive 12-volt battery terminals, then wait at least three minutes.
2. Remove the front pillar finishers. Refer to
INT-16, "Removal and Installation"
.
3. Put selector lever in the drive (D) position, then remove selector lever knob. Refer to
4. Remove the cluster lid D (1).
5. Remove console finisher. Refer to
TM-27, "Removal and Installation"
6. Remove the storage bin (1) or CD changer finisher (if equipped).
1.
Center speaker grille
2.
Tweeter speaker grille (LH)
3.
Instrument panel
4.
Instrument side mask (LH)
5.
Combination meter
6.
Lower knee protector (LH)
7.
Cluster lid A
8.
Instrument lower cover (LH)
9.
Fuse block cover
10. Steering column cover upper
11. Steering column cover lower
12. Console side finisher (LH)
13. CD changer finisher (if equipped)
14. Storage bin
15. Cup holder
16. Console rear finisher (with ventilator grille) 17. CVT finisher
18. Console
19. Console side finisher (RH)
20. Cluster lid D
21. Cluster lid C
22. Center ventilator grilles
23. Glove box assembly
24. Instrument side mask (RH)
25. Tweeter speaker grille (RH)
Clip
Metal clip
Pawl
ALJIA0036ZZ
ALJIA0017ZZ
![](/vehicles/gon/sttello/nita/isou.png)
INSTRUMENT PANEL ASSEMBLY
IP-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
7. Remove both instrument side masks (1).
8. Open the fuse block cover, remove the instrument lower cover
screw (A), then remove the instrument lower cover (1).
• Disconnect the harness connectors.
• Disconnect the aspirator tube.
9. Remove both the console side finishers.
10. Remove the console upper screws (A).
11. Remove the console side screws (A).
ALJIA0018ZZ
ALJIA0019ZZ
ALJIA0022ZZ
ALJIA0023ZZ
![](/vehicles/gon/sttello/nita/zalowa.png)
IP-14
< ON-VEHICLE REPAIR >
INSTRUMENT PANEL ASSEMBLY
12. Remove the console rear screws (A), then disconnect the con-
sole harness connector and remove the console assembly.
13. Open the glove box door, remove the glove box assembly
screws (A).
• Glove box assembly (1)
14. Remove the glove box assembly lower screws (A), then remove
the glove box assembly.
15. Remove the steering wheel. Refer to
ST-8, "Removal and Installation"
16. Remove the steering column cover screws (A), then remove
both the steering column cover upper (1) and steering column
cover lower (2).
ALJIA0024ZZ
ALJIA0020ZZ
ALJIA0021ZZ
ALJIA0025ZZ
![](/vehicles/gon/sttello/nita/viachimathat.png)
INSTRUMENT PANEL ASSEMBLY
IP-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
17. Remove the cluster lid A (1).
18. Remove the combination meter screws (A), then remove the
combination meter (1).
• Disconnect the harness connector.
19. Remove the spiral cable. Refer to
SRS-8, "Removal and Installation"
.
20. Disconnect the combination switch connector and remove the combination switch assembly.
21. Remove the center ventilator grilles (1).
ALJIA0026ZZ
ALJIA0027ZZ
ALJIA0029ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст