Nissan Altima HL32 Hybrid. Manual — part 1034
B1145 – B1148 SIDE CURTAIN AIR BAG MODULE RH
SRC-33
< COMPONENT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
Replace the related harness.
>> END
![](/vehicles/gon/sttello/nita/plcor.png)
SRC-34
< COMPONENT DIAGNOSIS >
B1086 – B1089 SEAT BELT PRE-TENSIONER LH
B1086 – B1089 SEAT BELT PRE-TENSIONER LH
Description
INFOID:0000000004495993
DTC B1086 – B1089 SEAT BELT PRE-TENSIONER LH
The seat belt pre-tensioner LH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit
will monitor for opens and shorts in detected lines to the seat belt pre-tensioner LH.
PART LOCATION
SRC-7, "SRS Component Parts Location"
DTC Logic
INFOID:0000000004495994
DTC DETECTION LOGIC
With CONSULT-lll
Without CONSULT-lll
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.
CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-lll.
Is the DTC detected?
YES
>> Refer to
SRC-35, "Diagnosis Procedure (Component Diagnosis)"
.
NO
>> Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.
IGNITION SWITCH
CONSULT-III name
DTC
DTC detecting condition
Repair order
PRE-TEN FRONT LH
[OPEN]
B1086
LH seat belt pre-tensioner circuit is open.
1.
Visually check the wiring harness connection.
2.
Replace the harness if it has visible damage.
3.
Replace the front LH seat belt pre-tensioner.
4.
Replace the air bag diagnosis sensor unit.
5.
Replace the related harness.
PRE-TEN FRONT LH
[VB-SHORT]
B1087
LH seat belt pre-tensioner circuit is shorted
to a power supply circuit.
PRE-TEN FRONT LH
[GND-SHORT]
B1088
LH seat belt pre-tensioner circuit is shorted
to ground.
PRE-TEN FRONT LH
[SHORT]
B1089
LH seat belt pre-tensioner circuits are
shorted to each other.
WHIA0263E
![](/vehicles/gon/sttello/nita/eewo.png)
B1086 – B1089 SEAT BELT PRE-TENSIONER LH
SRC-35
< COMPONENT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
Turn ignition switch ON.
>> GO TO 2
2.
IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3
3.
WAIT TIME
Wait more than 3 seconds.
>> GO TO 4
4.
REPEAT STEPS
Repeat steps 1 to 3 twice.
>> GO TO 5
5.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 6
6.
DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to
.
>> END
Diagnosis Procedure (Component Diagnosis)
INFOID:0000000004495995
Recheck SRS after each replacement.
1.
HARNESS CONNECTOR
Is there any visible damage to the connector?
YES or NO
YES
>> Replace the harness.
NO
>> GO TO 2
2.
WIRING HARNESS
Is there any visible damage to the harness?
YES or NO
YES
>> Replace the harness.
NO
>> GO TO 3
3.
FRONT LH SEAT BELT PRE-TENSIONER
Replace the front LH seat belt pre-tensioner. Refer to
SB-7, "Removal and Installation"
>> GO TO 4
4.
AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. Refer to
SRS-16, "Removal and Installation"
.
>> GO TO 5
5.
RELATED HARNESS
SRC-36
< COMPONENT DIAGNOSIS >
B1086 – B1089 SEAT BELT PRE-TENSIONER LH
Replace the related harness.
>> END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст