Nissan Altima HL32 Hybrid. Manual — part 752
![](/vehicles/gon/sttello/nita/pevexa.png)
SQUEAK AND RATTLE TROUBLE DIAGNOSES
INT-7
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Clip and Fastener
INFOID:0000000004491019
• Clips and fasteners in EXT section correspond to the following numbers and symbols.
• Replace any clips and/or fasteners which are damaged during removal or installation.
LAIA0071E
![](/vehicles/gon/sttello/nita/xhan.png)
INT-8
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Symbol
No.
Shapes
Removal & Installation
C101
C103
C203
C205
C206
CE103
CE107
SBF302H
SBF367BA
SBT095
SBF423H
SBF258G
LIIA0236E
MBT080A
SBF638CA
MBF519B
MBF520B
SBF104B
SBF147B
SBF411H
SBF767B
![](/vehicles/gon/sttello/nita/rustera.png)
SQUEAK AND RATTLE TROUBLE DIAGNOSES
INT-9
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
CE117
CF110
CF118
CG101
CS101
CR103
Metal Clip
Symbol
No.
Shapes
Removal & Installation
SBF174D
SBF175DA
SBF648B
SBF649B
SBF151D
SBF259G
SBF145B
SBF085B
SBF078B
SBF992G
SBF768B
SBF770B
WBT072
WBT073
INT-10
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSION-
ER"
INFOID:0000000004215418
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000004507211
NOTE:
• Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both 12-volt battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both 12-
volt battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the 12-volt battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the 12-volt battery disconnected or discharged, follow the proce-
dure below before starting the repair operation.
OPERATION PROCEDURE
1. Connect both 12-volt battery cables.
NOTE:
Supply power using jumper cables if 12-volt battery is discharged.
2. Carry the Intelligent Key or insert it to the key slot and turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3. Disconnect both 12-volt battery cables. The steering lock will remain released with both 12-volt battery
cables disconnected and the steering wheel can be turned.
4. Perform the necessary repair operation.
5. When the repair work is completed, re-connect both 12-volt battery cables. With the brake pedal released,
turn the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steer-
ing wheel will lock when the push-button ignition switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT-III.
Precautions For High-Voltage System
INFOID:0000000004215419
GI-24, "Precautions For High-Voltage System"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст