Nissan March K13. Manual — part 323
EXT-14
< REMOVAL AND INSTALLATION >
REAR BUMPER
6.
Pull bumper fascia assembly toward the vehicle out side as
shown by the arrows in the figure, and then disengage the
bumper fascia assembly from bumper side brackets (LH/RH).
7.
Remove bumper fascia assembly.
CAUTION:
When removing bumper fascia, 2 workers are required so as to prevent it from dropping.
8.
Remove the following parts after removing bumper fascia.
• Bumper side brackets (LH/RH)
• Rear panel lower
9.
Remove bumper energy absorber.
10. Remove mounting nuts, and then remove bumper stay.
INSTALLATION
Note the following item, and then Install in the reverse order of removal.
NOTE:
After installing, perform fitting adjustment.
: Pawl
JMKIA5400ZZ
JMKIA5404ZZ
Portion
Clearance
Surface height difference
Rear bumper – Rear fender
A – A
(
−
1.7) – (+0.3) mm
[(
−
0.067) – (+0.012) in]
0.0 – 1.0 mm
(0.000 – 0.039 in)
Rear bumper – Rear combi-
nation lamp
B – B
(
−
0.5) – (+3.5) mm
[(
−
0.020) – (+0.138) in]
—
Rear bumper – Back door
C – C
5.0 – 7.0 mm
(0.197 – 0.276 in)
—
COWL TOP
EXT-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
COWL TOP
Exploded View
INFOID:0000000006052869
Removal and Installation
INFOID:0000000006052870
REMOVAL
1.
Remove front wiper arm, and blades (LH,RH). Refer to
XX-XX, "*****"
.
2.
Remove front fender cover.
3.
Remove cowl top cover fixing clips.
4.
Pull forward to release cowl top cover from windshield glass.
CAUTION:
When performing the procedure after removing cowl top
cover, protect the lower of windshield glass with urethane
etc.
5.
Disconnect wind washer tube connector.
6.
Remove cowl top cover.
1.
Cowl top cover
2.
Cowl top cover seal
3.
Cowl cover oneway valve
4.
EPT sealer [3.0 mm (0.118 in)]
: Clip
: Vehicle front
Refer to
for symbols in the figure.
JMKIA5385ZZ
JMKIA3819ZZ
EXT-16
< REMOVAL AND INSTALLATION >
COWL TOP
7.
Remove the following parts after removing cowl top cover.
• EPT sealer
• Cowl top cover seal
• Washer tube
• Washer nozzles. Refer to
XX-XX, "*****"
.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
• Always replace cowl top cover EPT sealer on rear of vehicle with a new one when installing old cowl
top cover.
• After installing, perform adjustment of wiper arm. Refer to
XX-XX, "*****"
.
FENDER PROTECTOR
EXT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
FENDER PROTECTOR
FENDER PROTECTOR
FENDER PROTECTOR : Exploded View
INFOID:0000000006052871
FENDER PROTECTOR : Removal and Installation
INFOID:0000000006052872
REMOVAL
1.
Remove front fender protector fixing screws and clips.
2.
Disengage fender clips and fender protector, and then remove fender protector.
INSTALLATION
Install in the reverse order of removal.
1.
Fender protector
2.
J nut
JMKIA5395ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст