Nissan March K13. Manual — part 452
MA-14
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE
4.
Fill radiator and reservoir tank with water and reinstall radiator cap.
• When engine coolant over flows disconnected heater hose, connect heater hose, and continue filling the
engine coolant.
5.
Install air duct (between air cleaner case and electric throttle control actuator). Refer to
6.
Run the engine and warm it up to normal operating temperature.
7.
Rev the engine two or three times under no-load.
8.
Stop the engine and wait until it cools down.
9.
Drain water from the system. Refer to
.
10. Repeat steps 1 through 9 until clear water begins to drain from radiator.
RESERVOIR TANK CAP
RESERVOIR TANK CAP : Inspection
INFOID:0000000006057340
• Check valve seat (A) of radiator cap.
- Check that valve seat is swollen to the extent that the edge of the
plunger cannot be seen when watching it vertically from the top.
- Check that valve seat has no soil and damage.
• Pull negative-pressure valve to open it, and that it close completely
when released.
- Check that there is no dirt or damage on the valve seat of radiator
cap negative-pressure valve.
- Check that there are no unusualness in the opening and closing
conditions of negative-pressure valve.
• Check radiator cap relief pressure.
- When connecting radiator cap to the radiator cap tester (commer-
cial service tool) (A) and the radiator cap tester adapter (commer-
cial service tool) (B), apply engine coolant to the cap seal surface.
• Replace radiator cap if there is an unusualness related to the above three.
CAUTION:
When installing radiator cap, thoroughly wipe out the radiator filler neck to remove any waxy residue
or foreign material.
RADIATOR
B : Metal plunger
JPBIA0108ZZ
SMA967B
Standard and Limit
: Refer to
PBIC5122J
ENGINE MAINTENANCE
MA-15
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
RADIATOR : Inspection
INFOID:0000000006057341
Check radiator for mud or clogging. If necessary, clean radiator as follows.
CAUTION:
• Be careful not to bend or damage radiator fins.
• When radiator is cleaned without removal, remove all surrounding parts such as radiator cooling fan
assembly and horns. Then tape harness and harness connectors to prevent water from entering.
1.
Apply water by hose to the back side of the radiator core vertically downward.
2.
Apply water again to all radiator core surfaces once per minute.
3.
Stop washing if any stains no longer flow out from radiator.
4.
Blow air into the back side of radiator core vertically downward.
• Use compressed air lower than 490 kPa (4.9 bar, 5 kg/cm
2
, 71 psi) and keep distance more than 30 cm
(11.81 in).
5.
Blow air again into all the radiator core surfaces once per minute until no water sprays out.
FUEL LINES
FUEL LINES : Inspection
INFOID:0000000006057342
Inspect fuel lines, fuel filler cap, and fuel tank for improper attach-
ment, leakage, cracks, damage, loose connections, chafing or dete-
rioration.
If necessary, repair or replace damaged parts.
AIR CLEANER FILTER
AIR CLEANER FILTER : Removal and Installation
INFOID:0000000006057329
REMOVAL
1.
Remove air duct (inlet).
2.
Remove air cleaner body assembly (2) with air cleaner filter (1).
INSTALLATION
Install in the reverse order of removal.
ENGINE OIL
ENGINE OIL : Draining
INFOID:0000000006057332
WARNING:
• Be careful not to get burned, as engine oil may be hot.
A
: Engine
B
: Fuel line
C
: Fuel tank
JPBIA0129ZZ
JPBIA3370ZZ
MA-16
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE
• Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin
contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand cleaner as
soon as possible.
1.
Warm up the engine, and check for engine oil leakage from engine components. Refer to
2.
Stop the engine and wait for 10 minutes.
3.
Loosen oil filler cap.
4.
Remove drain plug and then drain engine oil.
ENGINE OIL : Refilling
INFOID:0000000006057333
1.
Install drain plug with new drain plug washer. Refer to
CAUTION:
Be sure to clean drain plug and install with new drain plug washer.
2.
Refill with new engine oil.
Engine oil specification and viscosity: Refer to
.
CAUTION:
• The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.
• Always use oil level gauge to determine the proper amount of engine oil in the engine.
3.
Warm up engine and check area around drain plug and oil filter for engine oil leakage.
4.
Stop engine and wait for 10 minutes.
5.
Check the engine oil level. Refer to
.
OIL FILTER
OIL FILTER : Removal and Installation
INFOID:0000000006057334
REMOVAL
1.
Using oil filter wrench [SST: KV10115801] (A), remove oil filter.
CAUTION:
• Oil filter is provided with relief valve. Use genuine NISSAN
oil filter or equivalent.
• Be careful not to get burned when engine and engine oil
may be hot.
• When removing, prepare a shop cloth to absorb any
engine oil leakage or spillage.
• Completely wipe off any engine oil that adheres to engine
and vehicle.
INSTALLATION
1.
Remove foreign materials adhering to the oil filter installation surface.
Tightening torque
: Refer to
.
Engine oil capacity
: Refer to
LU-13, "Periodical Maintenance Specification"
: Vehicle front
JPBIA3418ZZ
ENGINE MAINTENANCE
MA-17
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
2.
Apply new engine oil to the oil seal contact surface of new oil fil-
ter.
3.
Screw oil filter manually until it touches the installation surface,
then tighten it by 2/3 turn (A). Or tighten to specification.
OIL FILTER : Inspection
INFOID:0000000006057335
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level. Refer to
.
2.
Start the engine, and check that there is no leakage of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level, and adjust the level. Refer to
.
SPARK PLUG
SPARK PLUG : Removal and Installation
INFOID:0000000006057330
REMOVAL
1.
Remove ignition coil. Refer to
.
2.
Remove spark plug with a spark plug wrench (commercial ser-
vice tool).
CAUTION:
Never drop or shock spark plug.
INSTALLATION
Install in the reverse order of removal.
SPARK PLUG : Inspection
INFOID:0000000006057331
INSPECTION AFTER REMOVAL
Use the standard type spark plug for normal condition.
SMA010
Oil filter:
: 17.7 N·m (1.8 kg-m, 13 ft-lb)
JPBIA0077ZZ
a
: 14 mm (0.55 in)
JPBIA0030ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст