Nissan March K13. Manual — part 105
HOOD LOCK
DLK-131
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HOOD LOCK
Exploded View
INFOID:0000000005949006
Removal and Installation
INFOID:0000000005949007
REMOVAL
1.
Remove remove hood lock assembly mounting bolts, and then remove hood lock assembly.
2.
Disconnect hood lock cable from hood lock assembly.
3.
Remove hood lock cable clip.
4.
Remove fender protector (RH). Refer to
EXT-17, "FENDER PROTECTOR : Removal and Installation"
.
5.
Remove hood lock opener lever.
6.
Disconnect hood lock cable from hood lock opener lever.
7.
Remove grommet on the lower dash, and pull the hood lock control cable toward the passenger compart-
ment.
CAUTION:
While pulling, never to damage (peeling) the outside of hood lock control cable.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never to bend cable too much, keeping the radius 100 mm (3.937 in) or more.
1.
Hood lock opener lever
2.
Hood lock control cable
3.
Hood lock assembly
: Clip
Refer to
JMKIA5352GB
DLK-132
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
HOOD LOCK
• Check that cable is not offset from the positioning grommet,
and apply the sealant to the grommet (at * mark) properly.
• Check that hood lock control cable is properly engaged with hood lock.
• After installation, perform hood fitting adjustment. Refer to
DLK-112, "HOOD ASSEMBLY : Adjust-
• After installation, perform hood lock control inspection. Refer to
.
Inspection
INFOID:0000000005949008
NOTE:
If the hood lock cable is bent or deformed, replace it.
1.
Check that secondary latch is properly engaged with secondary striker [6.8 mm (0.268 in)] by hood
weight.
2.
While operating hood opener, carefully check that the front end of hood is raised by approximately 20.0
mm (0.787 in). Also check that hood opener returns to the original position.
3.
Check that hood opener operating is condition 49 N (5.0 kg, 11.0 lb) or below.
4.
Install so that static closing face of hood is 94 – 490 N·m (9.6 – 50.0 kg-m, 69 – 361 ft – lb).
NOTE:
• Exert vertical force on right side and left side of hood lock.
• Never press simultaneously both sides.
5.
Check the hood lock lubrication condition. If necessary, apply body grease to hood lock.
PIIB5801E
FRONT DOOR LOCK
DLK-133
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT DOOR LOCK
Exploded View
INFOID:0000000005949009
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000005949010
REMOVAL
1.
Remove outside handle. Refer to
DLK-134, "OUTSIDE HANDLE : Removal and Installation"
.
2.
Remove inside handle. Refer to
DLK-134, "INSIDE HANDLE : Removal and Installation"
.
3.
Disconnect door lock actuator connector.
4.
Remove front door lower sash (rear). Refer to
5.
Remove door lock assembly TORX bolts, and then remove door lock assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check door open/close, lock/unlock operation after installation.
• Check door lock cable is properly engaged with outside handle bracket.
1.
Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)
2.
Outside handle
3.
Front gasket
4.
Inside handle
5.
Clip
6.
TORX bolt
7.
Door lock assembly
8.
Key rod (driver side)
9.
Outside handle bracket
10. Rear gasket
: Pawl
: Vehicle front
Refer to
JMKIA5353GB
DLK-134
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000005949012
REMOVAL
1.
Remove front door finisher. Refer to
INT-14, "Removal and Installation"
2.
Remove upper side of sealing screen.
NOTE:
Cut the butyl tape so that some parts of the butyl tape do not remain on the sealing screen, if the sealing
screen is reused.
3.
Remove inside handle mounting bolts, slide handle toward rear of vehicle, disengage handle from door
panel, and remove inside handle.
4.
Remove the lock and inside handle cable from inside handle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000005949014
REMOVAL
1.
Fully close the front door glass.
2.
Remove front door finisher. Refer to
INT-14, "Removal and Installation"
3.
Remove sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
4.
Disconnect key rod (driver side).
5.
Disconnect door antenna and door request switch connector and remove harness clamp (with Intelligent
Key system) on outside handle bracket.
6.
Remove door side grommet, and loosen TORX bolt from grom-
met hole.
7.
While pulling outside handle (1), remove door key cylinder
assembly (diver side) (2) or outside handle escutcheon (passen-
ger side) (2).
JMKIA1464ZZ
JMKIA0441ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст