Nissan Quest E52. Manual — part 806
![](/vehicles/gon/llomit/zowi/ndanee.png)
BODY SIDE TRIM
INT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
1.
Disengage rear kicking plate fixing clips and pawls using a
remover tool (A).
2.
Hold the lower edge of rear kicking plate. Remove rear kicking
plate while rotating it upward avoiding the portion overlapped
with second seat.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing, check in advance that clips are accurately aligned with the holes on body panel side,
and then install by pressing in.
BODY SIDE WELT
BODY SIDE WELT : Removal and Installation
INFOID:0000000009650284
CAUTION:
• Never excessively pull body side welt.
• Never damage the body.
REMOVAL
FRONT BODY SIDE WELT
1.
Remove front kicking plate. Refer to
INT-22, "KICKING PLATE : Removal and Installation"
.
2.
Remove front body side welt.
REAR BODY SIDE WELT
1.
Remove rear kicking plate. Refer to
INT-22, "KICKING PLATE : Removal and Installation"
2.
Remove rear body side welt.
INSTALLATION
FRONT BODY SIDE WELT
Align body side welt identification color and vehicle position mark, and then install.
: Clip
: Pawl
JMJIA6204ZZ
JMJIA6205ZZ
JMJIA6206ZZ
![](/vehicles/gon/llomit/zowi/osenday.png)
INT-24
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
REAR BODY SIDE WELT
Install upper portion and both side surfaces in numerical order as
shown in the figure.
1.
Align body side welt identification color and vehicle position mark.
2.
Install vehicle upper.
3.
Install vehicle rear.
4.
Install vehicle front.
5.
Engage both ends using spacer (A), and then install lower portion.
6.
Install vehicle lower.
DASH SIDE FINISHER
DASH SIDE FINISHER : Removal and Installation
INFOID:0000000009650285
CAUTION:
Never damage the body.
REMOVAL
1.
Remove front body side welt. Refer to
INT-23, "BODY SIDE WELT : Removal and Installation"
.
2.
Remove dash side finisher.
: Vehicle front
JMJIA4852ZZ
JMJIA6207ZZ
![](/vehicles/gon/llomit/zowi/fanliso.png)
BODY SIDE TRIM
INT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Pull dash side finisher toward vehicle inside, disengage fixing
clips, and then remove dash side finisher.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing, check in advance that clips are accurately aligned with the holes on body panel side,
and then install by pressing in.
CENTER PILLAR LOWER GARNISH
CENTER PILLAR LOWER GARNISH : Removal and Installation
INFOID:0000000009650286
CAUTION:
• When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
• Never damage the body.
REMOVAL
1.
Fully open front door and slide door.
2.
Slide front seat to the fully forward position. Tilt seatback forward.
3.
Remove front kicking plate and rear kicking plate. Refer to
INT-22, "KICKING PLATE : Removal and
.
4.
Remove front body side welt and rear body side welt. Refer to
INT-23, "BODY SIDE WELT : Removal and
.
5.
Remove front seat belt outer anchor. Refer to
SB-5, "SEAT BELT RETRACTOR : Removal and Installa-
6.
Remove center pillar lower garnish.
a.
Disengage center pillar lower garnish fixing pawls and metal
clips using a remover tool (A).
b.
Disconnect harness connector. (with power sliding)
c.
Remove center pillar lower garnish.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing, check in advance that metal clips are accurately aligned with the holes on body panel
side, and then install by pressing in.
CENTER PILLAR UPPER GARNISH
: Clip
JMJIA6208ZZ
: Pawl
: Metal clip
JMJIA6209ZZ
![](/vehicles/gon/llomit/zowi/bren.png)
INT-26
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
CENTER PILLAR UPPER GARNISH : Removal and Installation
INFOID:0000000009650287
CAUTION:
• When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
• Never damage the body.
• Fabric upholstered parts are easily damaged. Be careful while performing work and storing parts.
REMOVAL
1.
Remove center pillar lower garnish. Refer to
INT-25, "CENTER PILLAR LOWER GARNISH : Removal
2.
Remove assist grip.
a.
Disengage assist grip cap fixing pawls using a remover tool (A).
CAUTION:
Apply protective tape (B) on the part to protect it from dam-
age.
b.
Remove assist grip fixing bolts, and then remove assist grip.
3.
Remove front seat belt shoulder anchor. Refer to
SB-5, "SEAT BELT RETRACTOR : Removal and Instal-
.
4.
Remove center pillar upper garnish cap.
Disengage center pillar upper garnish cap fixing pawl using a
remover tool (A).
CAUTION:
Apply protective tape (B) on the part to protect it from dam-
age.
5.
Remove center pillar upper garnish fixing bolt.
6.
Remove center pillar upper garnish.
Disengage center pillar upper garnish fixing clip using a remover
tool (A), and then remove center pillar upper garnish.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing, check in advance that clips are accurately aligned with the holes on body panel side,
and then install by pressing in.
REAR PILLAR GARNISH
: Pawl
JMJIA4857ZZ
: Pawl
JMJIA4856ZZ
: Clip
JMJIA4858ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст