Nissan Pathfinder. Manual — part 1163
![](/vehicles/gon/kidor/ruse/geeng.png)
P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A
TM-111
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10E]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace transaxle assembly. Refer to
TM-214, "Removal and Installation"
2.
CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (CVT FLUID TEMPERATURE SENSOR) (PART 1)
1. Disconnect the TCM connector.
2. Check continuity between TCM harness connector terminals and CVT unit harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (CVT FLUID TEMPERATURE SENSOR) (PART 2)
Check continuity between TCM harness connector terminals and ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-49, "Intermittent Incident"
.
NO
>> Repair or replace damaged parts.
CVT unit
Condition
Resistance
(Approx.)
Connector
Terminal
F209
12 – 18
CVT fluid temperature: 20
°C (68°F)
6.5 k
Ω
CVT fluid temperature: 50
°C (122°F)
2.2 k
Ω
CVT fluid temperature: 80
°C (176°F)
0.87 k
Ω
TCM
CVT unit
Continuity
Connector
Terminal
Connector
Terminal
F15
11
F46
18
Existed
12
12
TCM
Ground
Continuity
Connector
Terminal
F15
11
Ground
Not existed
12
![](/vehicles/gon/kidor/ruse/miti.png)
TM-112
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10E]
P0712 TRANSMISSION FLUID TEMPERATURE SENSOR A
P0712 TRANSMISSION FLUID TEMPERATURE SENSOR A
DTC Logic
INFOID:0000000009177568
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine and wait for 10 seconds or more.
2. Check the first trip DTC.
Is “P0712” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009177569
1.
CHECK CIRCUIT BETWEEN TCM AND CVT UNIT
1. Turn ignition switch OFF.
2. Disconnect TCM connector and CVT unit connector.
3. Check continuity between TCM harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning part.
2.
CHECK TERMINAL CODE ASSEMBLY
Check continuity between CVT unit connector terminal and ground
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace transaxle assembly. Refer to
TM-214, "Removal and Installation"
.
3.
CHECK CVT FLUID TEMPERATURE SENSOR
Check resistance between CVT unit connector terminals.
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible causes
P0712
FLUID TEMP SENSOR A
(Transmission Fluid Tempera-
ture Sensor A Circuit Low)
When all of the following conditions are satis-
fied and this state is maintained for 5 seconds:
• TCM power supply voltage: More than 11 V
• Fluid temperature sensor detection voltage:
0.15 V or less
• Harness or connector
(CVT fluid temperature sensor circuit is
shorted to ground)
• CVT fluid temperature sensor
TCM
—
Continuity
Connector
Terminal
F15
12
Ground
Not existed
CVT unit
—
Continuity
Connector
Terminal
F209
12
Ground
Not existed
![](/vehicles/gon/kidor/ruse/dre.png)
P0712 TRANSMISSION FLUID TEMPERATURE SENSOR A
TM-113
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10E]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-49, "Intermittent Incident"
.
NO
>> Replace transaxle assembly. Refer to
TM-214, "Removal and Installation"
.
CVT unit
Condition
Resistance
(Approx.)
Connector
Terminal
F209
12 – 18
CVT fluid temperature: 20
°C (68°F)
6.5 k
Ω
CVT fluid temperature: 50
°C (122°F)
2.2 k
Ω
CVT fluid temperature: 80
°C (176°F)
0.87 k
Ω
![](/vehicles/gon/kidor/ruse/resint.png)
TM-114
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10E]
P0713 TRANSMISSION FLUID TEMPERATURE SENSOR A
P0713 TRANSMISSION FLUID TEMPERATURE SENSOR A
DTC Logic
INFOID:0000000009177570
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Maintain the following condition for 10 seconds or more.
3. Stop the vehicle.
4. Check the first trip DTC.
Is “P0713” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009177571
1.
CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector and CVT unit connector.
3. Check continuity between TCM harness connector terminals and CVT unit harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning parts.
2.
CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (PART 2)
1. Turn ignition switch ON.
2. Check voltage between TCM harness connector terminal and ground.
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible causes
P0713
FLUID TEMP SENSOR A
(Transmission Fluid Tempera-
ture Sensor A Circuit High)
When all of the following conditions are satis-
fied and this state is maintained for 5 seconds:
• TCM power supply voltage: More than 11 V
• Vehicle speed: More than 10 km/h (7 MPH)
• Fluid temperature sensor detection voltage:
2.48 V or more
• Harness or connector
(CVT fluid temperature sensor circuit is
open or shorted to power supply)
• CVT fluid temperature sensor
Vehicle speed
: 20 km/h (12 MPH) or more
TCM
CVT unit
Continuity
Connector
Terminal
Connector
Terminal
F15
11
F46
18
Existed
12
12
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст