Nissan Almera Tino V10 (2001 year). Manual — part 115
![](/vehicles/gon/icup/oulends/tesa.png)
Wiring Diagram — F/FOG —
NLEL0428
MODELS WITH FUSE AND FUSIBLE LINK BOX E43
NLEL0428S01
YEL882B
FRONT FOG LAMP
Wiring Diagram — F/FOG —
EL-95
![](/vehicles/gon/icup/oulends/tavet.png)
MODELS WITH FUSE AND FUSIBLE LINK BOX E90
NLEL0428S02
YEL408C
FRONT FOG LAMP
Wiring Diagram — F/FOG — (Cont’d)
EL-96
![](/vehicles/gon/icup/oulends/ons.png)
NEL715
Bulb Replacement
NLEL0314
The front fog lamp is a semi-sealed beam type which uses a
replaceable halogen bulb.
+
Grasp only the plastic base when handling the bulb. Never
touch the glass envelope.
1.
Disconnect the battery cable.
2.
Disconnect the harness connector.
3.
Remove the front fog lamp bulb carefully. Do not shake the
bulb when removing it.
4.
Install in the reverse order of removal.
CAUTION:
+
Do not leave front fog lamp reflector without bulb for a
long period of time. Dust, moisture, smoke, etc. entering
front fog lamp body may affect the performance of the
front fog lamp. Remove front fog lamp bulb from the front
fog lamp reflector just before a replacement bulb is
installed.
FRONT FOG LAMP
Bulb Replacement
EL-97
![](/vehicles/gon/icup/oulends/rinishenknal.png)
NEL714
Aiming Adjustment
=NLEL0029
Before performing aiming adjustment, make sure of the following.
1)
Keep all tires inflated to correct pressure.
2)
Place vehicle on level ground.
3)
See that vehicle is unloaded (except for full levels of coolant,
engine oil and fuel, and spare tire, jack, and tools). Have the
driver or equivalent weight placed in driver’s seat.
Adjust aiming in the vertical direction by turning the adjusting
screw.
MEL327G
1.
Set the distance between the screen and the center of the fog
lamp lens as shown at left.
2.
Remove front fog lamp rim. For detail, refer to “BODY END” in
BT section.
3.
Turn front fog lamps ON.
NEL716
4.
Adjust front fog lamps so that the top edge of the high inten-
sity zone is 91 to 136 mm (3.58 to 5.35 in) below the height of
the fog lamp centers as shown at left.
+
When performing adjustment, if necessary, cover the head-
lamps and opposite fog lamp.
FRONT FOG LAMP
Aiming Adjustment
EL-98
![](/vehicles/gon/icup/oulends/xike.png)
Wiring Diagram — R/FOG —
NLEL0429
MODELS WITH FUSE AND FUSIBLE LINK BOX E43
NLEL0429S01
YEL883B
REAR FOG LAMP
Wiring Diagram — R/FOG —
EL-99
![](/vehicles/gon/icup/oulends/ain.png)
MODELS WITH FUSE AND FUSIBLE LINK BOX E90
NLEL0429S02
YEL409C
REAR FOG LAMP
Wiring Diagram — R/FOG — (Cont’d)
EL-100
System Description
NLEL0430
TURN SIGNAL OPERATION
NLEL0430S01
Power is supplied at all times
+
through 15A fuse [No. 5, located in fuse block (J/B)]
+
to time control unit terminal 9
With the ignition switch in the ON or START position, power is supplied
+
through 10A fuse [No. 10, located in fuse block (J/B)]
+
to time control unit terminal 1
Ground is supplied to time control unit terminal 16 through body grounds M28 and M48.
LH Turn
NLEL0430S0101
When the turn signal switch is moved to the L position, ground is supplied from body grounds E24 and E73
to
+
time control unit terminal 2
+
through turn signal switch terminals 3 and 1
With ground is supplied, time control unit controls the flashing of the LH turn signal lamps.
RH Turn
NLEL0430S0102
When the turn signal switch is moved to the R position, ground is supplied from body grounds E30 and E73
to
+
time control unit terminal 4
+
through turn signal switch terminals 2 and 1
With ground is supplied, time control unit controls the flashing of the RH turn signal lamps.
HAZARD LAMP OPERATION
NLEL0430S02
Power is supplied at all times
+
through 15A fuse [No. 5, located in fuse block (J/B)]
+
to time control unit terminal 9
Ground is supplied to time control unit terminal 16 through body grounds M28 and M48.
With the hazard switch in the ON position, ground is supplied from body grounds M28 and M48 to
+
time control unit terminal 5
+
through hazard switch terminals 6 and 4
With ground is supplied, time control unit controls the flashing of the hazard warning lamps.
HAZARD REMINDER OPERATION FOR MULTI-REMOTE CONTROL SYSTEM
NLEL0430S04
When the doors are locked or unlocked by multi-remote controller, time control unit controls turn lamps haz-
ard reminder flashes as follows.
+
Locked operation: Flash once
+
Unlock operation: Flash twice
TURN SIGNAL AND HAZARD WARNING LAMPS
System Description
EL-101
![](/vehicles/gon/icup/oulends/onigowh.png)
Wiring Diagram — TURN —
NLEL0431
MODELS WITH FUSE AND FUSIBLE LINK BOX E43
NLEL0431S01
YEL884B
TURN SIGNAL AND HAZARD WARNING LAMPS
Wiring Diagram — TURN —
EL-102
![](/vehicles/gon/icup/oulends/zwhas.png)
YEL885B
TURN SIGNAL AND HAZARD WARNING LAMPS
Wiring Diagram — TURN — (Cont’d)
EL-103
![](/vehicles/gon/icup/oulends/qulel.png)
MODELS WITH FUSE AND FUSIBLE LINK BOX E90
NLEL0431S02
YEL410C
TURN SIGNAL AND HAZARD WARNING LAMPS
Wiring Diagram — TURN — (Cont’d)
EL-104
![](/vehicles/gon/icup/oulends/aro.png)
YEL411C
TURN SIGNAL AND HAZARD WARNING LAMPS
Wiring Diagram — TURN — (Cont’d)
EL-105
![](/vehicles/gon/icup/oulends/blomb.png)
Trouble Diagnoses
NLEL0432
Symptom
Possible cause
Repair order
Turn signal and hazard warning
lamps do not operate.
1. Time control unit
2. Time control unit circuit
1. Check power door lock operation.
2. Check power supply and ground circuit for time con-
trol unit.
Turn signal lamps do not operate
but hazard warning lamps operate.
1. Turn signal switch
2. Open in turn signal switch cir-
cuit
1. Check turn signal switch.
2. Check turn signal switch ground for open circuit.
Hazard warning lamps do not
operate but turn signal lamps
operate.
1. Hazard switch
2. Open in hazard switch circuit
1. Check hazard switch.
2. Check hazard switch ground for open circuit.
Front turn signal lamp LH or RH
does not operate.
1. Bulb
2. Open in front turn signal lamp
circuit
1. Check bulb.
2. Check power supply and ground circuit for front turn
signal lamp.
Side turn signal lamp LH or RH
does not operate.
1. Bulb
2. Open in rear combination lamp
circuit
1. Check bulb.
2. Check power supply and ground circuit for rear com-
bination lamp.
Rear combination lamp LH or RH
does not operate.
1. Bulb
2. Open in side turn signal lamp
circuit
1. Check bulb.
2. Check grounds check power supply and ground circuit
for rear combination lamp.
LH and RH turn indicators do not
operate.
1. Ground
1. Check grounds E24·E73 (RHD models) or M28·M48
(LHD models)
LH or RH turn indicator does not
operate.
1. Bulb
1. Check bulb in combination meter.
TURN SIGNAL AND HAZARD WARNING LAMPS
Trouble Diagnoses
EL-106
![](/vehicles/gon/icup/oulends/paoo.png)
Schematic
NLEL0433
MODELS WITH FUSE AND FUSIBLE LINK BOX E43
NLEL0433S01
YEL886B
ILLUMINATION
Schematic
EL-107
![](/vehicles/gon/icup/oulends/ssthawe.png)
MODELS WITH FUSE AND FUSIBLE LINK BOX E90
NLEL0433S02
YEL412C
ILLUMINATION
Schematic (Cont’d)
EL-108
![](/vehicles/gon/icup/oulends/trs.png)
Wiring Diagram — ILL —
NLEL0434
MODELS WITH FUSE AND FUSIBLE LINK BOX E43
NLEL0434S01
YEL887B
ILLUMINATION
Wiring Diagram — ILL —
EL-109
![](/vehicles/gon/icup/oulends/knoot.png)
YEL888B
ILLUMINATION
Wiring Diagram — ILL — (Cont’d)
EL-110
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст