Nissan Murano. Manual — part 510
EC-150
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
POWER SUPPLY AND GROUND CIRCUIT
4.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
11.
CHECK 15 A FUSE
1.
Disconnect 15 A fuse (No. 50) from IPDM E/R.
2.
Check 15 A fuse.
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> Replace 15 A fuse.
12.
CHECK ECM POWER SUPPLY CIRCUIT-VI
1.
Disconnect ECM harness connector.
2.
Disconnect IPDM E/R harness connector.
3.
Check the continuity between ECM harness connector and IPDM E/R harness connector.
4.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
13.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
.
NO
>> Repair or replace harness or connectors.
ECM
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
E16
105
E10
10
Existed
U0101 CAN COMM CIRCUIT
EC-151
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
U0101 CAN COMM CIRCUIT
Description
INFOID:0000000009719880
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
DTC Logic
INFOID:0000000009719881
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 3 seconds.
2.
Check DTC.
Is DTC detected?
YES
>>
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009719882
LAN-18, "Trouble Diagnosis Flow Chart"
.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
U0101
Lost communication
with TCM
When ECM is not transmitting or receiving CAN
communication signal of OBD (emission-related
diagnosis) with TCM for 2 seconds or more.
• CAN communication line between
TCM and ECM
• CAN communication line open or
shorted
EC-152
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
U0164 CAN COMM CIRCUIT
U0164 CAN COMM CIRCUIT
Description
INFOID:0000000009719883
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
DTC Logic
INFOID:0000000009719884
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 3 seconds.
2.
Check DTC.
Is DTC detected?
YES
>>
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009719885
Go to
LAN-18, "Trouble Diagnosis Flow Chart"
.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
U0164
Lost communication
with Unified meter and
A/C amp.
When ECM is not transmitting or receiving CAN com-
munication signal of OBD (emission related diagno-
sis) with Unified meter and A/C amp. for 2 seconds or
more.
• CAN communication line between
Unified meter and A/C amp. and
ECM
• CAN communication line open or
shorted
U1001 CAN COMM CIRCUIT
EC-153
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
U1001 CAN COMM CIRCUIT
Description
INFOID:0000000009719886
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
DTC Logic
INFOID:0000000009719887
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 3 seconds.
2.
Check DTC.
Is DTC detected?
YES
>>
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009719888
LAN-18, "Trouble Diagnosis Flow Chart"
.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
U1001
CAN communication
line
When ECM is not transmitting or receiving CAN com-
munication signal other than OBD (emission related
diagnosis) for 2 seconds or more.
• Harness or connectors
(CAN communication line is open or
shorted)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст