Nissan Murano. Manual — part 576
EC-414
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P2118 THROTTLE CONTROL MOTOR
P2118 THROTTLE CONTROL MOTOR
Description
INFOID:0000000009720163
The throttle control motor is operated by the ECM and it opens and closes the throttle valve.
The current opening angle of the throttle valve is detected by the throttle position sensor. The throttle position
sensor provides feedback to the ECM, when opens/closes the throttle valve in response to driving conditions
via the throttle control motor.
DTC Logic
INFOID:0000000009720164
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 2 seconds.
2.
Start engine and let it idle for 5 seconds.
3.
Check DTC.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009720165
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Check ground connection E38. Refer to Ground Inspection in
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace ground connections.
2.
CHECK THROTTLE CONTROL MOTOR OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Disconnect electric throttle control actuator harness connector.
2.
Disconnect ECM harness connector.
3.
Check the continuity between electric throttle control actuator harness connector and ECM harness con-
nector.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P2118
Throttle control motor
circuit short
ECM detects short in both circuits between
ECM and throttle control motor.
• Harness or connectors
(Throttle control motor circuit is shorted.)
• Electric throttle control actuator
(Throttle control motor)
P2118 THROTTLE CONTROL MOTOR
EC-415
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
4.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning part.
3.
CHECK THROTTLE CONTROL MOTOR
EC-415, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 5.
4.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness or connectors.
5.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1.
Replace electric throttle control actuator. Refer to
.
2.
Go to
EC-415, "Special Repair Requirement"
.
>> INSPECTION END
Component Inspection
INFOID:0000000009720166
1.
CHECK THROTTLE CONTROL MOTOR
1.
Turn ignition switch OFF.
2.
Disconnect electric throttle control actuator harness connector.
3.
Check resistance between electric throttle control actuator terminals as per the following.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1.
Replace electric throttle control actuator. Refer to
.
2.
Go to
EC-413, "Special Repair Requirement"
.
>> INSPECTION END
Special Repair Requirement
INFOID:0000000009720167
1.
PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
EC-19, "THROTTLE VALVE CLOSED POSITION LEARNING : Special Repair Requirement"
Electric throttle control actuator
ECM
Continuity
Connector
Terminal
Connector
Terminal
F29
5
F7
5
Not existed
6
Existed
6
5
Existed
6
Not existed
Terminals
Resistance
5 and 6
Approx. 1 - 15
Ω
[at 25
°
C (77
°
F)]
EC-416
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P2118 THROTTLE CONTROL MOTOR
>> GO TO 2.
2.
PERFORM IDLE AIR VOLUME LEARNING
EC-20, "IDLE AIR VOLUME LEARNING : Special Repair Requirement"
>> END
P2119 ELECTRIC THROTTLE CONTROL ACTUATOR
EC-417
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P2119 ELECTRIC THROTTLE CONTROL ACTUATOR
Description
INFOID:0000000009720168
Electric throttle control actuator consists of throttle control motor, throttle position sensor, etc.
The throttle control motor is operated by the ECM and it opens and closes the throttle valve.
The throttle position sensor detects the throttle valve position, and the opening and closing speed of the throt-
tle valve and sends the voltage signals to the ECM. The ECM judges the current opening angle of the throttle
valve from these signals and opens/closes the throttle valve in response to driving conditions via the throttle
control motor.
DTC Logic
INFOID:0000000009720169
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A AND B
1.
Turn ignition switch ON and wait at least 1 second.
2.
Shift selector lever to the D position and wait at least 3 seconds.
3.
Shift selector lever to the P position.
4.
Turn ignition switch OFF and wait at least 10 seconds.
5.
Turn ignition switch ON and wait at least 1 second.
6.
Shift selector lever to the D position and wait at least 3 seconds.
7.
Shift selector lever to the P position.
8.
Turn ignition switch OFF, wait at least 10 seconds, and then turn ON.
9.
Check DTC.
Is DTC detected?
YES
>> Go to
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION C
1.
Turn ignition switch ON and wait at least 1 second.
2.
Shift selector lever to the D position and wait at least 3 seconds.
3.
Shift selector lever to the N or P position.
4.
Start engine and let it idle for 3 seconds.
5.
Check DTC.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P2119
Electric throttle control
actuator
A)
Electric throttle control actuator does not func-
tion properly due to the return spring malfunc-
tion.
• Electric throttle control actuator
B)
Throttle valve opening angle in fail-safe mode is
not in specified range.
C)
ECM detects that the throttle valve is stuck
open.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст