Nissan Murano. Manual — part 964
LAN
MAIN LINE BETWEEN M&A AND DLC CIRCUIT
LAN-167
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 7)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
MAIN LINE BETWEEN M&A AND DLC CIRCUIT
Diagnosis Procedure
INFOID:0000000010092916
1.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Disconnect the following harness connectors.
-
ECM
-
Combination meter
4.
Check the continuity between the combination meter harness connector and the data link connector.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the combination meter and the data link con-
nector.
NO
>> Repair the main line between the combination meter and the data link connector.
Combination meter harness connector
Data link connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
M34
21
M4
6
Existed
22
14
Existed
LAN-168
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 7)]
MAIN LINE BETWEEN DLC AND TCM CIRCUIT
MAIN LINE BETWEEN DLC AND TCM CIRCUIT
Diagnosis Procedure
INFOID:0000000010092917
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the following terminals and connectors for damage, bend and loose connection (connector side
and harness side).
-
Harness connector M11
-
Harness connector E105
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1.
Disconnect the harness connectors M11 and E105.
2.
Check the continuity between the data link connector and the harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair the main line between the data link connector and the harness connector M11.
3.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1.
Disconnect the harness connectors E6 and F123.
2.
Check the continuity between the harness connectors.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the data link connector and the TCM.
NO
>> Repair the main line between the harness connectors E105 and E6.
Data link connector
Harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
M4
6
M11
12
Existed
14
11
Existed
Harness connector
Harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
E105
12
E6
1
Existed
11
8
Existed
LAN
ECM BRANCH LINE CIRCUIT
LAN-169
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 7)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ECM BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000010092918
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the following terminals and connectors for damage, bend and loose connection (unit side and con-
nector side).
-
Models with automatic back door system
•
ECM
•
Harness connector E104
•
Harness connector B4
-
Models without automatic back door system
•
ECM
•
Harness connector E105
•
Harness connector M11
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect the connector of ECM.
2.
Check the resistance between the ECM harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the ECM branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the ECM. Refer to
Is the inspection result normal?
YES (Present error)>>Replace the ECM. Refer to
EC-16, "ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement"
YES (Past error)>>Error was detected in the ECM branch line.
NO
>> Repair the power supply and the ground circuit.
ECM harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
E16
98
97
Approx. 108 – 132
LAN-170
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 7)]
ADP BRANCH LINE CIRCUIT
ADP BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000010092919
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the following terminals and connectors for damage, bend and loose connection (unit side and con-
nector side).
-
Driver seat control unit
-
Harness connector B460
-
Harness connector B19
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect the connector of driver seat control unit.
2.
Check the resistance between the driver seat control unit harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the driver seat control unit branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the driver seat control unit. Refer to
CONTROL UNIT : Diagnosis Procedure"
Is the inspection result normal?
YES (Present error)>>Replace the driver seat control unit. Refer to
ADP-210, "Removal and Installation"
YES (Past error)>>Error was detected in the driver seat control unit branch line.
NO
>> Repair the power supply and the ground circuit.
Driver seat control unit harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
B452
23
24
Approx. 54 – 66
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст