Nissan Murano. Manual — part 385
TOUCH SENSOR
DLK-151
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
TOUCH SENSOR
RH
RH : Description
INFOID:0000000009719089
The touch sensor RH is installed on the right edge of the back door, and it detects any trapped foreign material
in the back door during the auto close operation and at the closure operation.
RH : Component Function Check
INFOID:0000000009719090
1.
CHECK FUNCTION
Check touch sensor RH (“TOUCH SEN RH”) in Data Monitor mode.
Is the inspection result normal?
YES
>> Touch sensor RH is OK.
NO
>> Refer to
DLK-151, "RH : Diagnosis Procedure"
RH : Diagnosis Procedure
INFOID:0000000009719091
1.
CHECK AUTOMATIC BACK DOOR CONTROL UNIT OUTPUT
1.
Turn ignition switch OFF.
2.
Disconnect touch sensor RH connector.
3.
Check voltage between touch sensor RH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK TOUCH SENSOR RH CIRCUIT
1.
Disconnect automatic back door control unit connector.
2.
Check continuity between automatic back door control unit harness connector and touch sensor RH har-
ness connector.
3.
Check continuity between automatic back door control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic back door control unit. Refer to
DLK-368, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK TOUCH SENSOR RH GROUND CIRCUIT
Monitor item
Condition
Status
TOUCH SEN RH
Touch sensor RH
Other than below
OFF
Detect obstruction
ON
(+)
(–)
Voltage (V)
(Approx.)
Touch sensor RH
Connector
Terminal
D164
1
Ground
6
Automatic back door control unit
Touch sensor RH
Continuity
Connector
Terminal
Connector
Terminal
B8
16
D164
1
Existed
Automatic back door control unit
Ground
Continuity
Connector
Terminal
B8
16
Not existed
DLK-152
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
TOUCH SENSOR
Check continuity between automatic back door control unit harness connector and touch sensor RH harness
connector.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK TOUCH SENSOR RH
DLK-152, "RH : Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace touch sensor RH. Refer to
DLK-354, "TOUCH SENSOR : Removal and Installation"
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
RH : Component Inspection
INFOID:0000000009719092
1.
CHECK TOUCH SENSOR RH
Check touch sensor RH.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace touch sensor RH. Refer to
DLK-354, "TOUCH SENSOR : Removal and Installation"
LH
LH : Description
INFOID:0000000009719093
The touch sensor LH is installed on the light edge of the back door, and it detects any trapped foreign material
in the back door during the auto close operation and at the closure operation.
LH : Component Function Check
INFOID:0000000009719094
1.
CHECK FUNCTION
Check touch sensor LH (“TOUCH SEN LH”) in Data Monitor mode.
Is the inspection result normal?
YES
>> Touch sensor LH is OK.
NO
>> Refer to
DLK-153, "LH : Diagnosis Procedure"
.
Automatic back door control unit
Touch sensor RH
Continuity
Connector
Terminal
Connector
Terminal
B8
15
D164
2
Existed
Terminal
Condition
Resistance
(Approx.)
Touch sensor RH
1
2
Touch sensor RH
Detect obstruction
120
Ω
or less
Other than above
1 k
Ω
±
10%
Monitor item
Condition
Status
TOUCH SEN LH
Touch sensor LH
Other than below
OFF
Detect obstruction
ON
TOUCH SENSOR
DLK-153
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
LH : Diagnosis Procedure
INFOID:0000000009719095
1.
CHECK AUTOMATIC BACK DOOR CONTROL UNIT OUTPUT
1.
Turn ignition switch OFF.
2.
Disconnect touch sensor LH connector.
3.
Check voltage between touch sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK TOUCH SENSOR LH CIRCUIT
1.
Disconnect automatic back door control unit.
2.
Check continuity between automatic back door control unit harness connector and touch sensor LH har-
ness connector.
3.
Check continuity between automatic back door control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic back door control unit. Refer to
DLK-368, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK TOUCH SENSOR LH GROUND CIRCUIT
Check continuity between automatic back door control unit harness connector and touch sensor LH harness
connector.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK TOUCH SENSOR LH
DLK-154, "LH : Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace touch sensor LH. Refer to
DLK-354, "TOUCH SENSOR : Removal and Installation"
.
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
(+)
(–)
Voltage (V)
(Approx.)
Touch sensor LH
Connector
Terminal
D165
1
Ground
6
Automatic back door control unit
Touch sensor LH
Continuity
Connector
Terminal
Connector
Terminal
B8
14
D165
1
Existed
Automatic back door control unit
Ground
Continuity
Connector
Terminal
B8
14
Not existed
Automatic back door control unit
Touch sensor LH
Continuity
Connector
Terminal
Connector
Terminal
B8
15
D165
2
Existed
DLK-154
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
TOUCH SENSOR
LH : Component Inspection
INFOID:0000000009719096
1.
CHECK TOUCH SENSOR LH
Check touch sensor LH.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace touch sensor LH. Refer to
DLK-354, "TOUCH SENSOR : Removal and Installation"
.
Terminal
Condition
Resistance
(Approx.)
Touch sensor LH
1
2
Touch sensor LH
Detect obstruction
120
Ω
or less
Other than above
1 k
Ω
±
10%
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст