Nissan Murano. Manual — part 505
EC-130
< SYSTEM DESCRIPTION >
[VQ35DE]
DIAGNOSIS SYSTEM (ECM)
How to Erase DTC and 1st Trip DTC
NOTE:
• If the ignition switch stays ON after repair work, be sure to turn ignition switch OFF once. Wait at least 10
seconds and then turn it ON (engine stopped) again.
• If the DTC is not for CVT related items (see
), skip step 1.
1.
Erase DTC in TCM. Refer to
2.
Select “ENGINE” with CONSULT.
3.
Select “SELF-DIAG RESULTS”.
4.
Touch “ERASE”. (DTC in ECM will be erased.)
Freeze Frame Data and 1st Trip Freeze Frame Data
*: The items are the same as those of 1st trip freeze frame data.
DATA MONITOR MODE
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitored Item
For reference values of the following items, refer to
Freeze frame data item*
Description
DIAG TROUBLE CODE
[PXXXX]
• The engine control component part/control system has a trouble code that is displayed as PXXXX. (Refer
FUEL SYS-B1
• “Fuel injection system status” at the moment a malfunction is detected is displayed.
• One of the following mode is displayed.
Mode2: Open loop due to detected system malfunction
Mode3: Open loop due to driving conditions (power enrichment, deceleration enleanment)
Mode4: Closed loop - using oxygen sensor(s) as feedback for fuel control
Mode5: Open loop - has not yet satisfied condition to go to closed loop
FUEL SYS-B2
CAL/LD VALUE [%]
• The calculated load value at the moment a malfunction is detected is displayed.
COOLANT TEMP [
°
C] or
[
°
F]
• The engine coolant temperature at the moment a malfunction is detected is displayed.
L-FUEL TRM-B1 [%]
• “Long-term fuel trim” at the moment a malfunction is detected is displayed.
• The long-term fuel trim indicates much more gradual feedback compensation to the base fuel schedule
than short-term fuel trim.
L-FUEL TRM-B2 [%]
S-FUEL TRM-B1 [%]
• “Short-term fuel trim” at the moment a malfunction is detected is displayed.
• The short-term fuel trim indicates dynamic or instantaneous feedback compensation to the base fuel
schedule.
S-FUEL TRM-B2 [%]
ENGINE SPEED [rpm]
• The engine speed at the moment a malfunction is detected is displayed.
VEHICL SPEED
[km/h] or [mph]
• The vehicle speed at the moment a malfunction is detected is displayed.
ABSOL TH·P/S [%]
• The throttle valve opening angle at the moment a malfunction is detected is displayed.
B/FUEL SCHDL [msec]
• The base fuel schedule at the moment a malfunction is detected is displayed.
INT/A TEMP SE [
°
C] or
[
°
F]
• The intake air temperature at the moment a malfunction is detected is displayed.
INT MANI PRES [kPa]
• These items are displayed but are not applicable to this model.
COMBUST CONDITION
DIAGNOSIS SYSTEM (ECM)
EC-131
< SYSTEM DESCRIPTION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Monitored item
Unit
Description
Remarks
ENG SPEED
rpm
• Indicates the engine speed computed from the
signal of the crankshaft position sensor (POS)
and camshaft position sensor (PHASE).
• Accuracy becomes poor if engine
speed drops below the idle rpm.
• If the signal is interrupted while the
engine is running, an abnormal value
may be indicated.
MAS A/F SE-B1
V
• The signal voltage of the mass air flow sensor is
displayed.
• When the engine is stopped, a certain
value is indicated.
• When engine is running, specification
range is indicated in “SPEC”.
B/FUEL SCHDL
msec
• “Base fuel schedule” indicates the fuel injection
pulse width programmed into ECM, prior to any
learned on board correction.
• When engine is running, specification
range is indicated in “SPEC”.
A/F ALPHA-B1
%
• The mean value of the air-fuel ratio feedback cor-
rection factor per cycle is indicated.
• When the engine is stopped, a certain
value is indicated.
• This data also includes the data for
the air-fuel ratio learning control.
• When engine is running, specification
range is indicated in “SPEC”.
A/F ALPHA-B2
COOLAN TEMP/S
°
C or
°
F
• The engine coolant temperature (determined by
the signal voltage of the engine coolant tempera-
ture sensor) is displayed.
• When the engine coolant temperature
sensor is open or short-circuited,
ECM enters fail-safe mode. The en-
gine coolant temperature determined
by the ECM is displayed.
A/F SEN1 (B1)
V
• The A/F signal computed from the input signal of
the air fuel ratio (A/F) sensor 1 is displayed.
A/F SEN1 (B2)
HO2S2 (B1)
V
• The signal voltage of the heated oxygen sensor 2
is displayed.
HO2S2 (B2)
HO2S2 MNTR(B1)
RICH/LEAN
• Display of heated oxygen sensor 2 signal:
RICH: means the amount of oxygen after three
way catalyst is relatively small.
LEAN: means the amount of oxygen after three
way catalyst is relatively large.
• When the engine is stopped, a certain
value is indicated.
HO2S2 MNTR(B2)
VHCL SPEED SE
km/h or mph
• The vehicle speed computed from the vehicle
speed signal sent from combination meter is dis-
played.
BATTERY VOLT
V
• The power supply voltage of ECM is displayed.
ACCEL SEN 1
V
• The accelerator pedal position sensor signal volt-
age is displayed.
• ACCEL SEN 2 signal is converted by
ECM internally. Thus, it differs from
ECM terminal voltage signal.
ACCEL SEN 2
TP SEN 1-B1
V
• The throttle position sensor signal voltage is dis-
played.
• TP SEN 2-B1 signal is converted by
ECM internally. Thus, it differs from
ECM terminal voltage signal.
TP SEN 2-B1
FUEL T/TMP SE
°
C or
°
F
• The fuel temperature (determined by the signal
voltage of the fuel tank temperature sensor) is
displayed.
INT/A TEMP SE
°
C or
°
F
• The intake air temperature (determined by the
signal voltage of the intake air temperature sen-
sor) is indicated.
EVAP SYS PRES
V
• The signal voltage of EVAP control system pres-
sure sensor is displayed.
FUEL LEVEL SE
V
• The signal voltage of the fuel level sensor is dis-
played.
START SIGNAL
ON/OFF
• Indicates start signal status [ON/OFF] computed
by the ECM according to the signals of engine
speed and battery voltage.
• After starting the engine, [OFF] is dis-
played regardless of the starter sig-
nal.
EC-132
< SYSTEM DESCRIPTION >
[VQ35DE]
DIAGNOSIS SYSTEM (ECM)
CLSD THL POS
ON/OFF
• Indicates idle position [ON/OFF] computed by
ECM according to the accelerator pedal position
sensor signal.
AIR COND SIG
ON/OFF
• Indicates [ON/OFF] condition of the air condition-
er switch as determined by the air conditioner sig-
nal.
P/N POSI SW
ON/OFF
• Indicates [ON/OFF] condition from the park/neu-
tral position (PNP) signal.
PW/ST SIGNAL
ON/OFF
• [ON/OFF] condition of the power steering system
(determined by the signal voltage of the power
steering pressure sensor) is indicated.
LOAD SIGNAL
ON/OFF
• Indicates [ON/OFF] condition from the electrical
load signal.
ON: Rear window defogger switch is ON and/or
lighting switch is in 2nd position.
OFF: Both rear window defogger switch and light-
ing switch are OFF.
IGNITION SW
ON/OFF
• Indicates [ON/OFF] condition from ignition switch
signal.
HEATER FAN SW
ON/OFF
• Indicates [ON/OFF] condition from the heater fan
switch signal.
BRAKE SW
ON/OFF
• Indicates [ON/OFF] condition from the stop lamp
switch signal.
INJ PULSE-B1
msec
• Indicates the actual fuel injection pulse width
compensated by ECM according to the input sig-
nals.
• When the engine is stopped, a certain
computed value is indicated.
INJ PULSE-B2
IGN TIMING
BTDC
• Indicates the ignition timing computed by ECM
according to the input signals.
• When the engine is stopped, a certain
value is indicated.
CAL/LD VALUE
%
• “Calculated load value” indicates the value of the
current air flow divided by peak air flow.
MASS AIRFLOW
g/s
• Indicates the mass air flow computed by ECM ac-
cording to the signal voltage of the mass air flow
sensor.
PURG VOL C/V
%
• Indicates the EVAP canister purge volume con-
trol solenoid valve control value computed by the
ECM according to the input signals.
• The opening becomes larger as the value in-
creases.
INT/V TIM (B1)
°
CA
• Indicates [
°
CA] of intake camshaft advance an-
gle.
INT/V TIM (B2)
INT/V SOL-B1
%
• The control value of the intake valve timing con-
trol solenoid valve (determined by ECM accord-
ing to the input signals) is indicated.
• The advance angle becomes larger as the value
increases.
INT/V SOL-B2
VIAS S/V-1
ON/OFF
• The control condition of the VIAS control solenoid
valve 1 (determined by ECM according to the in-
put signals) is indicated.
ON: VIAS control solenoid valve 1 is operating.
OFF: VIAS control solenoid valve 1 is not operat-
ing.
VIAS S/V-2
ON/OFF
• The control condition of the VIAS control solenoid
valve 2 (determined by ECM according to the in-
put signals) is indicated.
ON: VIAS control solenoid valve 2 is operating.
OFF: VIAS control solenoid valve 2 is not operat-
ing.
Monitored item
Unit
Description
Remarks
DIAGNOSIS SYSTEM (ECM)
EC-133
< SYSTEM DESCRIPTION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
AIR COND RLY
ON/OFF
• The air conditioner relay control condition (deter-
mined by ECM according to the input signals) is
indicated.
ENGINE MOUNT
IDLE/TRVL
• The control condition of the electronic controlled
engine mount (determined by ECM according to
the input signals) is indicated.
IDLE: Engine speed is below 950 rpm
TRVL: Engine speed is above 950 rpm
FUEL PUMP RLY
ON/OFF
• Indicates the fuel pump relay control condition
determined by ECM according to the input sig-
nals.
VENT CONT/V
ON/OFF
• The control condition of the EVAP canister vent
control valve (determined by ECM according to
the input signals) is indicated.
ON: Closed
OFF: Open
THRTL RELAY
ON/OFF
• Indicates the throttle control motor relay control
condition determined by the ECM according to
the input signals.
COOLING FAN
HI/MID/LOW/
OFF
• The control condition of the cooling fan (deter-
mined by ECM according to the input signals) is
indicated.
HI: High speed operation
MID: Middle speed operation
LOW: Low speed operation
OFF: Stop
HO2S2 HTR (B1)
ON/OFF
• Indicates [ON/OFF] condition of heated oxygen
sensor 2 heater determined by ECM according to
the input signals.
HO2S2 HTR (B2)
I/P PULLY SPD
rpm
• Indicates the engine speed computed from the in-
put speed sensor signal.
VEHICLE SPEED
km/h or mph
• The vehicle speed computed from the vehicle
speed signal sent from TCM is displayed.
IDL A/V LEARN
YET/CMPLT
• Displays the condition of idle air volume learning
YET: Idle Air Volume Learning has not been per-
formed yet.
CMPLT: Idle Air Volume Learning has already
been performed successfully.
ENG OIL TEMP
°
C or
°
F
• The engine oil temperature (determined by the
signal voltage of the engine oil temperature sen-
sor) is displayed.
TRVL AFTER MIL
km or mile
• Distance traveled while MIL is activated.
A/F S1 HTR(B1)
%
• Air fuel ratio (A/F) sensor 1 heater control value
computed by ECM according to the input signals.
• The current flow to the heater becomes larger as
the value increases.
A/F S1 HTR(B2)
AC PRESS SEN
V
• The signal voltage from the refrigerant pressure
sensor is displayed.
VHCL SPEED SE
km/h or mph
• The vehicle speed computed from the vehicle
speed signal sent from combination meter is dis-
played.
SET VHCL SPD
km/h or mph
• The preset vehicle speed is displayed.
MAIN SW
ON/OFF
• Indicates [ON/OFF] condition from MAIN switch
signal.
CANCEL SW
ON/OFF
• Indicates [ON/OFF] condition from CANCEL
switch signal.
Monitored item
Unit
Description
Remarks
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст