Qashqai J11. Audio, Visual & Navigation System — part 17
![](/vehicles/gon/haine/fre/stug.png)
AV
NORMAL OPERATING CONDITION
AV-257
< SYMPTOM DIAGNOSIS >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Location Correction by Map-Matching is Slow
• The map-matching function needs to refer to the data of the surrounding area. It is necessary to drive some
distance for the function to work.
• Because map-matching operates on this principle, when there are many roads running in similar directions
in the surrounding area, no matching determination may be made. The location may not be corrected until
some special feature is found.
Name of Road is Not Displayed
The current road name may not be displayed if there are no road names displayed on the map screen.
Contents of Display Differ for Birdview™ and the (Flat) Map Screen
Difference of the BIRDVIEW™ screen from the flat map screen are as follows.
• The current place name displays names which are primarily in the direction of vehicle travel.
• The amount of time before the vehicle travel or turn angle is updated on the screen is longer than for the
(flat) map display.
• The conditions for display of place names, roads, and other data are different for nearby areas and for more
distant areas.
• Some thinning of the character data is done to prevent the display becoming too complex. In some cases
and in some locations, the display contents may differ.
• The same place name, street name, etc. may be displayed multiple times.
Vehicle Mark Shows a Position Which is Completely Wrong
In the following cases, the vehicle mark may appear on completely different position in the map depending on
the GPS satellite signal receiving conditions. In this case, perform location correction and direction correction.
• When location correction has not been done
- If the receiving conditions of the GPS satellite signal is poor, if the vehicle mark becomes out of place, it may
move to a completely different location and not come back if location correction is not done. The position will
be corrected if the GPS signal can be received.
• When the vehicle has traveled by ferry, or when the vehicle has been being towed
Precautions
for driving
Just after the engine is started
If the vehicle is driven just after the engine
is started when the gyroscope (angular
speed sensor) correction is not completed,
the vehicle can lose its direction and may
have deviated from the correct location.
Wait for a short while before
driving after starting the engine.
Continuous driving without stopping
When driving long distances without stop-
ping, direction errors may accumulate, and
the current-location mark may deviate from
the correct road.
Stop and adjust the orientation.
Abusive driving
Spinning the wheels or engaging in other
kinds of abusive driving may result in the
system being unable perform correct detec-
tion, and may cause the vehicle mark to de-
viate from the correct road.
If after travelling about 10 km (6
miles) the correct location has
not been restored, perform lo-
cation correction and, if neces-
sary, direction correction.
How to cor-
rect location
Position correction accuracy
If the accuracy of location settings is poor,
accuracy may be reduced when the correct
road cannot be found, particularly in places
where there are many roads.
Enter in the road displayed on
the screen with an accuracy of
approx. 1mm.
Caution: Whenever possible,
use detailed map for the correc-
tion.
Direction when location is corrected
If the accuracy of location settings during
correction is poor, accuracy may be re-
duced afterwards.
Perform direction correction.
Cause (condition)
–: While driving
ooo: Display
Driving condition
Remarks (correction, etc.)
SEL701V
SEL702V
AV-258
< SYMPTOM DIAGNOSIS >
[NAVIGATION]
NORMAL OPERATING CONDITION
- Because calculation of the current location cannot be done when traveling with the ignition off, for example
when traveling by ferry or when being towed, the location before travel is displayed. If the precise location
can be detected with GPS, the location will be corrected.
Vehicle Mark Jumps
In the following cases, the vehicle mark may appear to jump as a result of automatic correction of the current
location.
• When map matching has been done
- If the current location and the vehicle mark are different when map matching is done, the vehicle mark may
seem to jump. At this time, the location may be “corrected” to the wrong road or to a location which is not on
a road.
• When GPS location correction has been done
- If the current location and the vehicle mark are different when the location is corrected using GPS measure-
ments, the vehicle mark may seem to jump. At this time, the location may be “corrected” to a location which
is not on a road.
Vehicle Mark is in a River or Sea
The navigation system moves the vehicle mark with no distinction between land and rivers or sea. If the vehi-
cle mark is somehow out of place, it may appear that the vehicle is driving in a river or the sea.
Vehicle Mark Automatically Rotates
The system wrongly memorizes the rotating status as stopping when the ignition switch is turned ON with the
turntable rotating. That causes the vehicle mark to rotate when the vehicle is stopped.
When Driving on Same Road, Sometimes Vehicle Mark is in Right Place and Sometimes it is in Wrong Place
The conditions of the GPS antenna (GPS data) and gyroscope (angular speed sensor) change gradually.
Depending on the road traveled and the operation of the steering wheel, the location detection results will be
different. Therefore, even on a road on which the location has never been wrong, conditions may cause the
vehicle mark to deviate.
![](/vehicles/gon/haine/fre/oourn.png)
AV
AV CONTROL UNIT
AV-259
< REMOVAL AND INSTALLATION >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
REMOVAL AND INSTALLATION
AV CONTROL UNIT
Exploded View
INFOID:0000000010435739
Removal and Installation
INFOID:0000000010435740
REMOVAL
CAUTION:
• Before disconnecting the AV control unit and battery terminals, turn the ignition switch OFF and wait
at least 30 seconds.
• Before replacing AV control unit, perform READ “CONFIGURATION” to save current vehicle specifi-
cation. Refer to
AV-179, "CONFIGURATION (AV CONTROL UNIT) : Configuration List"
.
NOTE:
After the ignition switch is turned OFF, the AV control unit continues operating for approximately 30 seconds.
Therefore, data corruption may occur if battery voltage is cut off within 30 seconds.
1.
Disconnect the negative battery terminal. Refer to
PG-155, "Removal and Installation"
2.
Remove A/C switch (AUTOMATIC AIR CONDITIONING) or front air control (MANUAL AIR CONDITION-
ING).
3.
Remove instrument finisher B. Refer to
4.
Remove instrument finisher E. Refer to
5.
Remove the AV control unit screws, then pull out the AV control unit.
6.
Disconnect the harness connectors from the AV control unit and remove.
7.
Remove the AV control unit bracket (LH/RH) screws and the AV control unit brackets (LH/RH) (if neces-
sary).
INSTALLATION
Installation is in the reverse order of removal.
1.
AV control unit bracket (LH)
2.
AV control unit
3.
AV control unit bracket (RH)
AWNIA3339ZZ
AV-260
< REMOVAL AND INSTALLATION >
[NAVIGATION]
AV CONTROL UNIT
CAUTION:
When replacing AV control unit, perform “WRITE CONFIGURATION”. Refer to
![](/vehicles/gon/haine/fre/yous.png)
AV
STEERING SWITCH
AV-261
< REMOVAL AND INSTALLATION >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
STEERING SWITCH
Exploded View
INFOID:0000000010435741
Removal and Installation
INFOID:0000000010435742
REMOVAL
NOTE:
The steering switches are serviced as an assembly.
1.
Remove steering wheel. Refer to
2.
Release pawls on the steering wheel rear finisher and remove.
3.
Remove screws (A) and steering switches (1) from steering
wheel (2).
INSTALLATION
Installation is in the reverse order of removal.
1.
Steering wheel rear finisher
2.
Steering wheel
3.
Steering switches
Pawl
AWNIA3342ZZ
AWNIA3326ZZ
AV-262
< REMOVAL AND INSTALLATION >
[NAVIGATION]
FRONT TWEETER
FRONT TWEETER
Removal and Installation
INFOID:0000000010435743
REMOVAL
1.
Remove defroster grille. Refer to
.
2.
Remove bolts and pull out the front tweeter.
3.
Disconnect the harness connector from the front tweeter and remove.
INSTALLATION
Installation is in the reverse order of removal.
![](/vehicles/gon/haine/fre/beakenot.png)
AV
FRONT DOOR SPEAKER
AV-263
< REMOVAL AND INSTALLATION >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
FRONT DOOR SPEAKER
Exploded View
INFOID:0000000010435744
Removal and Installation
INFOID:0000000010435745
REMOVAL
1.
Remove front door finisher. Refer to
INT-12, "FRONT DOOR FINISHER : Exploded View"
2.
Remove front door speaker bolts, then pull out front door speaker.
3.
Disconnect the harness connector from front door speaker and remove.
INSTALLATION
Installation is in the reverse order of removal.
ALNIA1580ZZ
1.
Front door speaker
![](/vehicles/gon/haine/fre/feves.png)
AV-264
< REMOVAL AND INSTALLATION >
[NAVIGATION]
REAR DOOR SPEAKER
REAR DOOR SPEAKER
Exploded View
INFOID:0000000010435746
Removal and Installation
INFOID:0000000010435747
REMOVAL
1.
Remove rear door finisher. Refer to
INT-15, "REAR DOOR FINISHER : Exploded View"
2.
Remove rear door speaker bolts, then pull out rear door speaker.
3.
Disconnect the harness connector from the rear door speaker and remove.
INSTALLATION
Installation is in the reverse order of removal.
1.
Rear door speaker
ALNIA1581ZZ
![](/vehicles/gon/haine/fre/lleran.png)
AV
USB INTERFACE AND AUX IN JACK
AV-265
< REMOVAL AND INSTALLATION >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
USB INTERFACE AND AUX IN JACK
Removal and Installation
INFOID:0000000010435748
REMOVAL
1.
Remove center console. Refer to
2.
Release the pawls (A) on the back of USB interface and AUX in
jack (2).
INSTALLATION
Installation is in the reverse order of removal.
ALNIA1582ZZ
![](/vehicles/gon/haine/fre/xanierse.png)
AV-266
< REMOVAL AND INSTALLATION >
[NAVIGATION]
MICROPHONE
MICROPHONE
Removal and Installation
INFOID:0000000010435749
REMOVAL
1.
Remove the map lamp assembly. Refer to
2.
Release harness connector (A) by sliding rearward to remove
from the pawl (B).
3.
Release pawls (C) and remove the microphone (1) from the
front room/map lamp assembly.
INSTALLATION
Installation is in the reverse order of removal.
ALNIA1583ZZ
![](/vehicles/gon/haine/fre/ckntepacevoo.png)
AV
AROUND VIEW MONITOR CONTROL UNIT
AV-267
< REMOVAL AND INSTALLATION >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
AROUND VIEW MONITOR CONTROL UNIT
Exploded View
INFOID:0000000010435750
Removal and Installation
INFOID:0000000010435751
REMOVAL
CAUTION:
Before replacing around view monitor control unit, save or print current vehicle specification with
CONSULT configuration before replacement. Refer to
AV-177, "ADDITIONAL SERVICE WHEN
REPLACING AROUND VIEW MONITOR CONTROL UNIT : Work Procedure"
1.
Remove glove box assembly. Refer to
.
2.
Remove around view monitor control unit screws.
3.
Disconnect the harness connector from the around view monitor control unit and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Replace the around view monitor control unit if it has been dropped or sustained an impact.
• When replacing around view monitor control unit, you must perform "After Replace ECU" with CON-
SULT. Refer to
AV-177, "ADDITIONAL SERVICE WHEN REPLACING AROUND VIEW MONITOR CON-
.
NOTE:
Perform camera image calibration. Refer to
AV-181, "CALIBRATING CAMERA IMAGE (AROUND VIEW
.
ALNIA1600ZZ
1.
Around view monitor control unit A.
Harness connector
![](/vehicles/gon/haine/fre/zand.png)
AV-268
< REMOVAL AND INSTALLATION >
[NAVIGATION]
FRONT CAMERA
FRONT CAMERA
Exploded View
INFOID:0000000010435752
Removal and Installation
INFOID:0000000010435753
REMOVAL
1.
Remove the front grille. Refer to
2.
Remove screws and front camera.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
Perform camera image calibration. Refer to
AV-181, "CALIBRATING CAMERA IMAGE (AROUND VIEW
.
1.
Front grille
2.
Front camera
ALNIA1612ZZ
![](/vehicles/gon/haine/fre/pemb.png)
AV
SIDE CAMERA
AV-269
< REMOVAL AND INSTALLATION >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SIDE CAMERA
Removal and Installation
INFOID:0000000010435754
REMOVAL
1.
Remove door mirror rear finisher (2). Refer to
2.
Remove screws (A) and side camera (1).
: Pawl
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Perform camera image calibration (if equipped with around view camera). Refer to
BRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Description"
ALLIA1383ZZ
![](/vehicles/gon/haine/fre/thay.png)
AV-270
< REMOVAL AND INSTALLATION >
[NAVIGATION]
REAR VIEW CAMERA
REAR VIEW CAMERA
Removal and Installation
INFOID:0000000010435755
REMOVAL
1.
Remove the back door outer finisher. Refer to
2.
Disconnect washer tubes (1,3) and air tube (2) (if equipped).
3.
Release pawl (B), disconnect harness connector (A) from rear
view camera and remove.
INSTALLATION
Installation is in the reverse order of removal.
AWNIA3329ZZ
AV
GPS ANTENNA
AV-271
< REMOVAL AND INSTALLATION >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
GPS ANTENNA
Removal and Installation
INFOID:0000000010435756
REMOVAL
1.
Remove instrument panel. Refer to
.
2.
Remove screw and the GPS antenna.
INSTALLATION
Installation is in the reverse order of removal.
AV-272
< REMOVAL AND INSTALLATION >
[NAVIGATION]
AUDIO ANTENNA
AUDIO ANTENNA
Removal and Installation
INFOID:0000000010435757
REMOVAL
1.
Remove the luggage side upper finisher (RH). Refer to
.
2.
Partially lower headlining (rear). Refer to
3.
Disconnect harness connectors from antenna feeder.
4.
Remove nut from audio antenna and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
If the audio antenna nut is not properly tightened, lower sensitivity of the antenna may be experi-
enced. If the nut is over tightened, this will deform the roof panel.
Audio antenna nut
: 6.5 N·m (0.66 kg-m, 58 in-lb)
![](/vehicles/gon/haine/fre/zlll.png)
AV
ANTENNA FEEDER
AV-273
< REMOVAL AND INSTALLATION >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
ANTENNA FEEDER
Feeder Layout
INFOID:0000000010435758
ANTENNA FEEDER LAYOUT
1.
Antenna base (antenna amp. and
satellite antenna)
2.
Rod Antenna
3.
M394
4.
M399
E1NIA0073ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст