Nissan Qashqai J11. Manual — part 652
![](/vehicles/gon/ffua/forullalerus/urd.png)
INPUT SHAFT AND GEAR
TM-183
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
12. Install 5th-6th synchronizer hub, 5th-6th spread springs, and 5th-6th shifting inserts onto 5th-6th coupling
sleeve.
CAUTION:
• Be careful with orientation of 5th-6th synchronizer hub.
• Never reuse 5th-6th synchronizer hub and 5th-6th cou-
pling sleeve.
• Replace 5th-6th synchronizer hub and 5th-6th coupling
sleeve as a set.
• Be careful with orientation of 5th-6th coupling sleeve.
• Be sure not to hook center projection of 2 spread springs
on same shifting insert.
13. Press in 5th-6th synchronizer hub assembly using the press
stand.
CAUTION:
Align grooves of 5th-6th shifting insert and 5th baulk ring.
A
:Transaxle front side
B
:Transaxle rear side
PCIB1883E
A
: 5th input gear side
B
: 6th input gear side
PCIB1884E
SCIA1083E
SCIA0928E
![](/vehicles/gon/ffua/forullalerus/eros.png)
TM-184
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
INPUT SHAFT AND GEAR
14. Install 6th needle bearing, 6th input gear, 6th baulk ring onto 6th
input gear bushing and then press in 6th input gear bushing onto
input shaft using the drift [SST: ST33200000].
15. Install snap ring onto input shaft and make sure that end play
(gap between snap ring and groove) of 6th input gear bushing
satisfies the standard value.
• If measurement is outside the standard range, select snap
ring.
CAUTION:
Never reuse snap ring.
16. Press in input shaft rear bearing using the drift [SST:
ST30901000].
CAUTION:
Install input shaft rear bearing with its brown surface facing
the 6th input gear side.
17. Press in input shaft front bearing using the drifts.
18. Install oil channel onto input shaft.
19. Check end play of 3rd, 4th, 5th, and 6th input gears.
WCIA0309E
End play standard value
:Refer to
SCIA0970E
WCIA0310E
PCIB0825E
End play standard value
: Refer to
.
SCIA0966E
![](/vehicles/gon/ffua/forullalerus/adg.png)
INPUT SHAFT AND GEAR
TM-185
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Inspection
INFOID:0000000010288522
INPUT SHAFT AND GEAR
Check items below. If necessary, replace them with new ones.
• Damage, peeling, dent, uneven wear, bending, etc. of shaft
• Excessive wear, damage, peeling, etc. of gears
• Excessive wear, damage, peeling, etc. of cam side of clutch gears
SYNCHRONIZER
Synchronizer Hub and Coupling Sleeve
Check items below. If necessary, replace them with new ones.
• Damage and excessive wear of contact surfaces of coupling
sleeve, synchronizer hub and shifting insert
• Coupling sleeve and synchronizer hub must move smoothly.
Baulk Ring and Spread Spring
Check items below. If necessary, replace them with new ones.
• If any crack, damage, or excessive wear is found on cam face of
baulk ring or working face of insert, replace it.
Baulk Ring Clearance for Single Cone Synchronizer (4th, 5th, and 6th)
Push baulk ring on the cone and measure the clearance between
baulk ring and cone. If measurement is below limit, replace it with a
new one.
Baulk Ring Clearance for Double Cone Synchronizer (3rd)
JPDIC0142ZZ
SMT387A
SMT867D
Clearance
Standard value
: Refer to
.
Limit value
: Refer to
.
SMT140
![](/vehicles/gon/ffua/forullalerus/rest.png)
TM-186
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
INPUT SHAFT AND GEAR
Check the clearance between outer baulk ring, synchronizer cone,
and inner baulk ring as follows.
CAUTION:
The clearances “A” and “B” are controlled with outer baulk
ring, synchronizer cone, and inner baulk ring as a set. Replace
them as a set if the clearances are outside the limit value.
1.
Measure the clearance “A” at 2 points or more diagonally oppo-
site using a dial indicator. And then calculate mean value.
2.
Measure the clearance “B” at 2 points or more diagonally oppo-
site using a feeler gauge. And then calculate mean value.
BEARING
Check items below. If necessary, replace them with new ones.
• Damage and rough rotation of bearing
SCIA0950E
Clearance “A”
Standard value
: Refer to
Limit value
: Refer to
SCIA0951E
Clearance “B”
Standard value
: Refer to
.
Limit value
: Refer to
.
SCIA1084E
MTF0041D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст