Nissan Qashqai J11. Manual — part 240
![](/vehicles/gon/ffua/forullalerus/ich.png)
ECH-258
< DTC/CIRCUIT DIAGNOSIS >
[HRA2DDT]
P10AA ECM
P10AA ECM
DTC Logic
INFOID:0000000010500704
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
Turn ignition switch OFF and wait at least 12 minutes.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine and let it idle for at least 5 second.
2.
Check DTC.
Is DTC detected?
YES
>> Proceed to
ECH-258, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010500705
1.
REPLACE ECM
1.
Replace ECM. Refer to
ECH-313, "Removal and Installation"
2.
Proceed to
>> INSPECTION END
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P10AA
CONTROL MODULE
(Control module)
ECM calculation function is malfunctioning.
ECM
![](/vehicles/gon/ffua/forullalerus/tnd.png)
P1512 STARTER MOTOR
ECH-259
< DTC/CIRCUIT DIAGNOSIS >
[HRA2DDT]
C
D
E
F
G
H
I
J
K
L
M
A
ECH
N
P
O
P1512 STARTER MOTOR
Description
INFOID:0000000010500706
ECM multiplies operation counter of starter motor which operated in operation with key switch and operation
with restart and memorizes it.
DTC Logic
INFOID:0000000010500707
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If the other DTC Confirmation Procedure is performed right before this procedure, the ignition switch must be
turned OFF and wait for 12 minutes or more to start this procedure.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 3 seconds.
2.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
ECH-259, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010500708
1.
REPLACE STARTER MOTOR
Replace starter motor. Refer to
STR-24, "HRA2DDT : Removal and Installation"
>> INSPECTION END
DTC
CONSULT screen terms
(Trouble diagnosis con-
tent)
DTC detecting condition
Possible cause
P1512
STARTER MOTOR
(Starter motor)
When starter motor operating counter which
ECM memorized is 250,000 times or more.
Starter motor
![](/vehicles/gon/ffua/forullalerus/yoncoutoabla.png)
ECH-260
< DTC/CIRCUIT DIAGNOSIS >
[HRA2DDT]
P1525 ASCD SYSTEM
P1525 ASCD SYSTEM
DTC Logic
INFOID:0000000010500712
DTC DETECTION LOGIC
NOTE:
DTC P1525 is displayed with another DTC.
Perform the trouble diagnosis for the corresponding DTC.
Diagnosis Procedure
INFOID:0000000010500713
1.
CHECK DTC
Perform “All DTC Reading” with CONSULT.
Is any DTC detected?
YES
>> Perform trouble diagnosis for DTC indicated.
NO
>> Erase the DTC.
DTC No.
CONSULT screen terms
(Trouble diagnosis con-
tent)
DTC detecting condition
Possible cause
P1525
CRUISE CONTROL/
SPEED LIMITER
(Cruise control/speed
limiter)
Other DTC that illuminates MIL is detected
while ASCD is operating.
• Harness or connectors
• Others systems
• ECM
![](/vehicles/gon/ffua/forullalerus/mea.png)
P1589 PARK/NEUTRAL POSITION SWITCH
ECH-261
< DTC/CIRCUIT DIAGNOSIS >
[HRA2DDT]
C
D
E
F
G
H
I
J
K
L
M
A
ECH
N
P
O
P1589 PARK/NEUTRAL POSITION SWITCH
DTC Logic
INFOID:0000000010500719
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM COMPONENT FUNCTION CHECK
NOTE:
Use Component Function Check the overall function of the neutral position switch circuit. During this check,
the DTC might not be confirmed.
1.
Turn ignition switch ON.
2.
Check the voltage between ECM harness connectors as per the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
ECH-261, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010500720
1.
CHECK FUSE
Check that the following fuse is not fusing.
Is the fuse fusing?
YES
>> Replace the fuse after repairing the applicable circuit.
NO
>> GO TO 2.
2.
CHECK REVERSE/NEUTRAL POSITION SWITCH POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect reverse/neutral position switch harness connector.
3.
Turn ignition switch ON.
4.
Check the voltage between reverse/neutral position switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P1589
NEUTRAL SWITCH
(Neutral switch)
Neutral position switch signal remains ON
for a long driving distance.
• Harness and connectors
(Neutral position switch circuit is
shorted.)
• Reverse/neutral position switch
+
−
Condition
Voltage
(Approx.)
ECM
Connector
Terminal
F18
143
Ground
Shift lever
Neutral
Battery voltage
Except above
0 V
Fuse No.
Capacity
#67
10 A
+
−
Voltage
(Approx.)
Reverse/Neutral position switch
Connector
Terminal
F100
2
Ground
Battery voltage
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст