Nissan Qashqai J11. Manual — part 2109
![](/vehicles/gon/ffua/inoowhem/zedernklin.png)
AV
PRECAUTIONS
AV-125
< PRECAUTION >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
5.
Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
INSTRUCTION 2 (FOR VEHICLES PARKED BY IGNITION SWITCH OFF)
1.
Unlock the door with intelligent key or remote keyless entry.
NOTE:
At this moment, ACC power is supplied.
2.
Open the driver side door.
3.
Open the hood.
4.
Close the driver side door.
5.
Wait at least 3 minutes.
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
6.
Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
• For vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON
the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of main battery and sub battery discon-
nected, then DTC may be detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
Precaution for Trouble Diagnosis
INFOID:0000000010435635
AV COMMUNICATION SYSTEM
• Do not apply voltage of 7.0 V or higher to the measurement terminals.
• Use the tester with its open terminal voltage being 7.0 V or less.
• Be sure to turn ignition switch OFF and disconnect the battery cable from the negative terminal before
checking the circuit.
Precaution for Harness Repair
INFOID:0000000010435636
AV COMMUNICATION SYSTEM
• Solder the repaired parts, and wrap with tape. [Frays of twisted line
must be within 110 mm (4.33 in).]
D4D engine
: 20 minutes
K9K engine
: 4 minutes
M9R engine
: 4 minutes
R9M engine
: 4 minutes
V9X engine
: 4 minutes
PKIA0306E
![](/vehicles/gon/ffua/inoowhem/litheyi.png)
AV-126
< PRECAUTION >
[NAVIGATION]
PRECAUTIONS
• Do not perform bypass wire connections for the repair parts. (The
spliced wire will become separated and the characteristics of
twisted line will be lost.)
Precaution for Work
INFOID:0000000010435637
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
PKIA0307E
![](/vehicles/gon/ffua/inoowhem/ici.png)
AV
PREPARATION
AV-127
< PREPARATION >
[NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000010435638
The actual shape of the tools may differ from those illustrated here.
Commercial Service Tools
INFOID:0000000010435639
Tool number
(TechMate No.)
Tool name
Description
—
(J-46534)
Trim Tool Set
Removing trim components
AWJIA0483ZZ
Tool name
Description
Power tool
Loosening nuts, screws and bolts
PIIB1407E
![](/vehicles/gon/ffua/inoowhem/rel.png)
AV-128
< SYSTEM DESCRIPTION >
[NAVIGATION]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000010435640
A. Center of back door
B. View with glove box removed
E1NIA0074ZZ
No.
Component
Function
1.
Rod antenna
Refer to
AV-131, "Rod Antenna, Antenna Amp., Satellite Antenna and Antenna
2.
Antenna base (antenna amp. and satellite
antenna)
3.
Rear door speaker RH
Refer to
4.
Front door speaker RH
5.
Front camera
Refer to
6.
Front door speaker LH
Refer to
7.
Side camera
Refer to
.
8.
Rear door speaker LH
Refer to
9.
Microphone
Refer to
10.
GPS antenna
Refer to
.
11.
Front tweeter LH
Refer to
12.
Steering angle sensor
Refer to
AV-131, "Steering Angle Sensor"
.
13.
Steering switches
Refer to
14.
Front tweeter RH
Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст