Nissan Qashqai J11. Manual — part 703
![](/vehicles/gon/ffua/forullalerus/ormauthery.png)
CONTROL CABLE
TM-387
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
13. Remove the control cable
from bracket
.
14. Remove the control cable from the vehicle.
INSTALLATION
Note the followings and install in the reverse order of removal.
• From below the vehicle, press the grommet
into place until the
pawls (
) make a click sound.
CAUTION:
• Place the grommet on the floor, then fasten it in place from
below the vehicle.
• Check that pulling down on the grommet does not discon-
nect it.
• Pay attention to the following when connecting the control cable to the CVT shift selector.
1.
Shift the selector lever and Manual lever to “P” position.
2.
When connecting the control cable
to the CVT shift selector
assembly
, face the grooved surface of the rib
up and insert
the control cable until it stops.
3.
Install the socket
onto the CVT shift selector assembly.
CAUTION:
• Place the socket onto the CVT shift selector assembly,
then fasten it in place from above.
• Check that the pulling on the socket does not disconnect
it.
Inspection and Adjustment
INFOID:0000000010668192
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT position. Refer to
INSPECTION AFTER ADJUSTMENT
: Vehicle front
JPDIA0107ZZ
JSDIA5182ZZ
JSDIA1624ZZ
JSDIA1810ZZ
TM-388
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
CONTROL CABLE
Check the CVT shift selector position after the adjustment. Refer to
![](/vehicles/gon/ffua/forullalerus/seea.png)
KEY INTERLOCK CABLE
TM-389
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
KEY INTERLOCK CABLE
Exploded View
INFOID:0000000010668193
Removal and Installation
INFOID:0000000010668194
REMOVAL
CAUTION:
Always apply the parking brake before performing removal and installation.
1.
Remove the lower instrument panel (driver side) and steering column cover. Refer to
.
2.
Remove the center console. Refer to
IP-19, "Removal and Installation"
.
3.
Press the pawls
of the key interlock cable slider
while slid-
ing it in the direction of the casing cap
, and separate the
adjusting holder
and slider.
4.
Remove the key interlock cable from the shift selector.
5.
Lift the clip
in the direction of the arrow (
) and remove in
the direction of the arrow (
).
6.
Remove the key interlock cable from the key cylinder.
7.
Disengage the clip and disconnect the key interlock cable from
the vehicle.
Shift selector assembly
Clip
Key interlock cable
Clip
Key cylinder
JSDIA5227ZZ
:Key interlock rod
JSDIA1797ZZ
: Key interlock cable
: Key cylinder
JSDIA1798ZZ
![](/vehicles/gon/ffua/forullalerus/fruthtra.png)
TM-390
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
KEY INTERLOCK CABLE
INSTALLATION
1.
Move the shift selector to "P" position.
2.
Turn the ignition switch to ACC or ON position.
3.
Install the holder of key interlock cable to key cylinder.
4.
Install the clip
in the direction of the arrow (
) and push it
in the direction of the arrow (
).
5.
Turn the ignition switch to LOCK position.
6.
Install the adjusting holder
onto the key interlock rod
, then
install the casing cap
onto the shift selector cable bracket
.
CAUTION:
• When installing the key interlock cable, do not bend or
twist the cable forcefully.
• After connecting the key interlock cable to the shift selec-
tor cable bracket, be sure to check that the casing cap is
completely fastened to the cable bracket. If the casing cap
is easily displaced, replace the key interlock cable.
7.
Slide the key interlock cable slider
toward the key interlock
rod
side and install the adjusting holder
and key interlock
rod.
CAUTION:
• Never squeeze the pawls on the key interlock cable slider
when holding the slider.
• Never apply force in a perpendicular direction to the key
interlock rod when sliding the slider.
8.
Install the center console. Refer to
9.
Install the lower instrument panel (driver side) and steering col-
umn cover. Refer to
IP-13, "Removal and Installation"
.
Inspection
INFOID:0000000010668195
INSPECTION AFTER INSTALLATION
• Check the CVT position. If a malfunction is found, adjust the CVT position. Refer to
.
• The key can be removed only when the selector lever is in the “P” position.
• It must not be possible to turn the ignition switch to LOCK when the selector lever is not in the “P” position.
: Key interlock cable
: Key cylinder
JSDIA3589ZZ
JSDIA1799ZZ
JSDIA2644ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст