Nissan Qashqai J11. Manual — part 915
![](/vehicles/gon/ffua/forullalerus/iourilokink.png)
PB-42
< BASIC INSPECTION >
CONFIGURATION (ELECTRIC PARKING BRAKE CONTROL MODULE)
CONFIGURATION (ELECTRIC PARKING BRAKE CONTROL MODULE)
Work Procedure
INFOID:0000000010833857
CAUTION:
• Use “Manual Configuration” only when “TYPE ID” of electric parking brake control module cannot
be read.
• After configuration, turn the ignition switch from OFF to ON and check that the brake system warn-
ing lamp turns OFF after staying illuminated for approximately two seconds.
• If an error occurs during configuration, start over from the beginning.
1.
CHECKING TYPE ID (1)
Use FAST (service parts catalogue) to search electric parking brake control module of the applicable vehicle
and find “Type ID”.
Is “Type ID” displayed?
YES
>> Print out “Type ID” and GO TO 2.
NO
>> “Configuration” is not required for electric parking brake control module. Replace in the usual
manner. Refer to
PB-142, "Removal and Installation"
.
2.
CHECKING TYPE ID (2)
CONSULT Configuration
1.
Select “Before Replace ECU” of “Read/Write Configuration”.
2.
Check that “Type ID” is displayed on the CONSULT screen.
Is “Type ID” displayed?
YES
>> GO TO 3.
NO
>> GO TO 7.
3.
VERIFYING TYPE ID (1)
CONSULT Configuration
Compare a “Type ID” displayed on the CONSULT screen with the one searched by using FAST (service parts
catalogue) to check that these “Type ID” agree with each other.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 4.
4.
SAVING TYPE ID
CONSULT Configuration
Save “Type ID” on CONSULT.
>> GO TO 5.
5.
REPLACING ELECTRIC PARKING BRAKE CONTROL MODULE (1)
Replace the electric parking brake control module. Refer to
PB-142, "Removal and Installation"
CAUTION:
Never perform the following work items:
• Change of system mode
• Calibration of G sensor
• Reset of clutch stroke sensor
• Adjustment of rear brake caliper initial position
• Operation of rear brake caliper
• Release of rear brake caliper
>> GO TO 6.
6.
WRITING (AUTOMATIC WRITING)
CONSULT Configuration
1.
Select “After Replace ECU” of “Re/programming, Configuration” or that of “Read / Write Configuration”.
CONFIGURATION (ELECTRIC PARKING BRAKE CONTROL MODULE)
PB-43
< BASIC INSPECTION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
>> End of work.
![](/vehicles/gon/ffua/forullalerus/xepa.png)
PB-44
< BASIC INSPECTION >
INSTRUCTIONS FOR RELEASING PARKING BRAKE WHERE PARKING
BRAKE SWITCH CANNOT BE USED
INSTRUCTIONS FOR RELEASING PARKING BRAKE WHERE PARKING
BRAKE SWITCH CANNOT BE USED
Description
INFOID:0000000010833858
Disconnecting the battery negative terminal with the parking brake on, prevents the parking brake from releas-
ing. Releasing is performed mechanically.
Work Procedure
INFOID:0000000010833859
1.
DISCONNECT PARKING BRAKE ACTUATOR HARNES CONNECTOR
1.
Disconnect the parking brake actuator harness connector
from the rear caliper assembly
.
>> GO TO 2.
2.
REMOVE PARKING BRAKE ACTUATOR
Remove the parking brake actuator
from the rear brake caliper
assembly .
>> GO TO 3.
3.
RELEASE OF PARKING BRAKE
Rotate the rear brake caliper assembly
spindle part
clockwise.
Is the parking brake released?
YES
>> GO TO 4.
NO
>> Check the rear brake caliper assembly. Refer to
"BRAKE CALIPER ASSEMBLY : Inspection and Adjust-
ment"
4.
REPLACE REAR CALIPER ASSEMBLY
Replace the rear caliper assembly. Refer to
BR-43, "BRAKE CALIPER ASSEMBLY : Removal and Installa-
.
CAUTION:
Never reuse the parking brake actuator.
>> End of work.
JSFIA2443ZZ
JSFIA2426ZZ
JSFIA2444ZZ
![](/vehicles/gon/ffua/forullalerus/unnde.png)
INSTRUCTIONS FOR RELEASING PARKING BRAKE WHERE PARKING
BRAKE SWITCH CANNOT BE USED
PB-45
< BASIC INSPECTION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
INSTRUCTIONS FOR RELEASING PARKING BRAKE WHERE PARKING
BRAKE SWITCH CANNOT BE USED
Description
INFOID:0000000010833858
Disconnecting the battery negative terminal with the parking brake on, prevents the parking brake from releas-
ing. Releasing is performed mechanically.
Work Procedure
INFOID:0000000010833859
1.
DISCONNECT PARKING BRAKE ACTUATOR HARNES CONNECTOR
1.
Disconnect the parking brake actuator harness connector
from the rear caliper assembly
.
>> GO TO 2.
2.
REMOVE PARKING BRAKE ACTUATOR
Remove the parking brake actuator
from the rear brake caliper
assembly .
>> GO TO 3.
3.
RELEASE OF PARKING BRAKE
Rotate the rear brake caliper assembly
spindle part
clockwise.
Is the parking brake released?
YES
>> GO TO 4.
NO
>> Check the rear brake caliper assembly. Refer to
"BRAKE CALIPER ASSEMBLY : Inspection and Adjust-
ment"
4.
REPLACE REAR CALIPER ASSEMBLY
Replace the rear caliper assembly. Refer to
BR-43, "BRAKE CALIPER ASSEMBLY : Removal and Installa-
.
CAUTION:
Never reuse the parking brake actuator.
>> End of work.
JSFIA2443ZZ
JSFIA2426ZZ
JSFIA2444ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст