Nissan Qashqai J11. Manual — part 998
![](/vehicles/gon/ffua/forullalerus/wen.png)
SB-6
< REMOVAL AND INSTALLATION >
FRONT SEAT BELT
REMOVAL AND INSTALLATION
FRONT SEAT BELT
Exploded View
INFOID:0000000010478340
SEAT BELT RETRACTOR
1.
Front seat belt
2.
Center pillar lower and upper
garnish assembly
3.
D-ring anchor fixing nut
4.
Seat belt height adjuster fixing
bolt
5.
Seat belt height adjuster
6.
Center pillar
7.
Seat belt retractor
8.
Seat belt retractor bolt
9.
Seat belt buckle bolt
10. Seat belt buckle
11.
Cover
12. Anchor plate fixing bolt
13. Seat belt label
14. Pre-tensioner
15. Anchor plate
for symbols in the figure
E1HIA0037GB
![](/vehicles/gon/ffua/forullalerus/pana.png)
FRONT SEAT BELT
SB-7
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SB
N
O
P
SEAT BELT RETRACTOR : Removal and Installation
INFOID:0000000010478341
REMOVAL
WARNING:
• Before servicing the SRS, turn the ignition switch off, disconnect both battery terminals then wait at
least three minutes.
• Do not drop the seat belt retractor. Always handle it with care.
• Always point pre-tensioner cylinder away from body when handling.
DRIVER SIDE
1.
Remove the center pillar lower and upper garnish. Refer to
.
2.
Remove D-ring anchor fixing nut.
3.
Disconnect seat belt from seat belt buckle.
4.
Remove seat belt buckle bolt.
5.
Disconnect pre-tensioner connector and remove seat belt buckle and pretensioner assembly.
CAUTION:
• For removing/installing the shoulder belt pre-tensioner
harness connector, insert a thin screwdriver wrapped in
tape into the notch, then lift the lock and remove the har-
ness connector as shown.
• Install the harness connector with the lock raised, and
push the lock into the harness connector as shown.
• After installing the harness connector, check that the lock
is pushed in securely.
6.
Disconnect the harness connector from the seat belt pre-tensioner.
CAUTION:
• For removing/installing the shoulder belt pre-tensioner
harness connector, insert a thin screwdriver wrapped in
tape into the notch, then lift the lock and remove the har-
ness connector as shown.
• Install the harness connector with the lock raised, and
push the lock into the harness connector as shown.
• After installing the harness connector, check that the lock
is pushed in securely.
7.
Remove seat belt retractor bolt and remove seat belt retractor.
Passenger side
1.
Remove the center pillar lower and upper garnish. Refer to
.
2.
Remove D-ring anchor fixing nut.
3.
Remove anchor plate fixing bolt.
4.
Disconnect the harness connector from the seat belt pre-tensioner.
CAUTION:
PHIA0953J
PHIA0953J
![](/vehicles/gon/ffua/forullalerus/vilun.png)
SB-8
< REMOVAL AND INSTALLATION >
FRONT SEAT BELT
• For removing/installing the shoulder belt pre-tensioner
harness connector, insert a thin screwdriver wrapped in
tape into the notch, then lift the lock and remove the har-
ness connector as shown.
• Install the harness connector with the lock raised, and
push the lock into the harness connector as shown.
• After installing the harness connector, check that the lock
is pushed in securely.
5.
Remove seat belt retractor bolt and remove seat belt retractor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Tighten the D-ring Anchor bolt, seat belt retractor bolts and seat belt buckle to specification. Refer to
• Make sure that the seat belt height adjuster is locked in the lowest position and is aligned with the
center pillar upper finisher opening during installation.
• Make sure both the D-ring anchor and seat belt height adjuster operate freely.
• Always perform an inspection after repair to make sure the system is functioning correctly.
SEAT BELT HEIGHT ADJUSTER
SEAT BELT HEIGHT ADJUSTER : Removal and Installation
INFOID:0000000010478342
REMOVAL
1.
Remove center pillar upper finisher. Refer to
.
2.
Remove D- ring anchor fixing nut.
3.
Remove seat belt height adjuster.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Make sure that the seat belt height adjuster is locked in the lowest position and is aligned with the
center pillar upper finisher opening during installation.
• Tighten the D-ring anchor bolt and seat belt height adjuster bolts to specification. Refer to
.
• Make sure both the D-ring anchor and seat belt height adjuster operate freely.
• Always perform an inspection after repair to make sure the system is functioning correctly.
FRONT SEAT BELT BUCKLE
FRONT SEAT BELT BUCKLE : Removal and Installation
INFOID:0000000010478343
REMOVAL
1.
Remove front seat. Refer to
SE-28, "Removal and Installation"
(Driver side) or
(Passenger side).
2.
Disconnect seat belt buckle harness connector.
3.
Remove seat belt buckle anchor bolt and seat belt buckle.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Tighten the seat belt buckle anchor bolt to specification. Refer to
.
PHIA0953J
FRONT SEAT BELT
SB-9
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SB
N
O
P
• Always perform an inspection after repair to make sure the system is functioning correctly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст