Nissan Qashqai J11. Manual — part 168
![](/vehicles/gon/ffua/forullalerus/zep.png)
CO-76
< REMOVAL AND INSTALLATION >
[K9K]
WATER PUMP
• Visually make sure there is no significant dirt or rusting on the
water pump body and vane.
• Make sure there is no looseness in the vane shaft, and that it turns
smoothly when rotated by hand.
• If there are any unusualness, replace the water pump assembly.
INSPECTION AFTER INSTALLATION
• Check for engine coolant leaks using reservoir tank cap tester. Refer to
MBIB0546E
![](/vehicles/gon/ffua/forullalerus/xwa.png)
THERMO PLUNGER UNIT
CO-77
< REMOVAL AND INSTALLATION >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
THERMO PLUNGER UNIT
Exploded View
INFOID:0000000010438937
for symbol marks in the figure.
Removal and Installation
INFOID:0000000010438938
REMOVAL
CAUTION:
Make sure that the engine is cool down before operating, in order to avoid hot coolant outflow, as the
electric pump is turned on even if the engine is off. On the other hand the pump is turned off when the
engine is on. In this case as the electric pump is working, the thermostat will have to stay open due to
high temperatures.
1.
Remove the battery negative cable.
2.
Lift the vehicle.
3.
Remove front fender protector (LH). Refer to
EXT-32, "Removal and Installation"
4.
Drain the engine coolant.
5.
Remove the ground cable bolt.
6.
Disconnect thermo plunger unit connector.
7.
Remove the thermo plunger connection caps.
8.
Remove the thermo plunger connection nuts using the appropriate tool.
9.
Remove the water hose from thermo plunger unit.
10. Remove the thermo plunger unit fixing bolts.
11. Remove the thermo plunger unit.
1.
Water hose
2.
Clamp Thermo plunger control unit
3.
Thermo plunger control unit
4.
Earth lead
5.
Bracket stay
6.
Water hose
7.
Water hose clip
E1BIA1144GB
![](/vehicles/gon/ffua/forullalerus/xxch.png)
CO-78
< REMOVAL AND INSTALLATION >
[K9K]
THERMO PLUNGER UNIT
INSTALLATION
NOTE:
• Thermo plunger caps must be correctly installed after removal.
• The hoses must be fully pushed onto pipe before tightening the clamp.
• Clamp must be fixed 5mm MIN from end of hose.
Installation is basically the reverse order of the removal.
Thermo plunger bracket stay bolt: 10 N.m (1 kg-m, 7 ft-lb)
![](/vehicles/gon/ffua/forullalerus/terefit.png)
THERMOSTAT
CO-79
< REMOVAL AND INSTALLATION >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
THERMOSTAT
Inspection
INFOID:0000000010416388
• Place a thread so that it is caught in the valves of the thermostat.
Immerse fully in a container filled with water. Heat while stirring.
(The example in the figure shows the thermostat.)
• The valve opening temperature is the temperature at which the
valve opens and falls from the thread.
• Continue heating. Check the full-open lift amount.
• After checking the full-open lift amount, lower the water tempera-
ture and check the valve closing temperature.
• If the measured value is out of the standard value or unusual valve
seating condition is found, replace water inlet and thermostat
assembly.
SLC949A
Items
Temperature
°
C (
°
F)
Start of opening
Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст