Nissan Qashqai J11. Manual — part 2013
![](/vehicles/gon/ffua/inoowhem/namerth.png)
PG-144
< WIRING DIAGRAM >
HARNESS LAYOUT
BACK DOOR No. 2 HARNESS
JRMIC4156GB
![](/vehicles/gon/ffua/inoowhem/verean.png)
PG
HARNESS LAYOUT
PG-145
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
RHD : Room Lamp Harness
INFOID:0000000010464095
JRMIC4899GB
![](/vehicles/gon/ffua/inoowhem/sarkengimarc.png)
PG
BATTERY INSPECTION
PG-147
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Work Flow WITHOUT STOP/START SYSTEM
INFOID:0000000010464099
OVERALL SEQUENCE
DETAILED FLOW
1.
VISUAL INSPECTION
1.
Check battery case for cracks or bends.
2.
Check battery terminals for damage.
Are these inspection results normal?
YES
>> GO TO 2.
NO
>> Replace battery.
2.
CAPACITY TEST
Check battery voltage.
Is the voltage 12.35 V or more?
YES
>> GO TO 3.
NO
>> GO TO 4.
3.
DISCHARGE
1.
Check battery type and determine the specified current using the table.
2.
Perform discharge using the load tester.
Is the voltage 10 V or more?
YES
>> Ready for use.
NO
>> Replace battery.
JSMIA1006GB
Type
Current (A)
55D23L-MF
300
80D23L-MF
![](/vehicles/gon/ffua/inoowhem/amyo.png)
PG-148
< BASIC INSPECTION >
BATTERY INSPECTION
4.
CHARGE
Charge battery, following the instructions below:
• Constant current charging may damage batteries. Therefore, charge battery by constant voltage charge
mode with the maximum voltage set at 15 V.
• Charge at least 6 hours or until the charge current becomes 4 amps or less.
>> GO TO 3.
Work Flow WITH STOP/START SYSTEM
INFOID:0000000011772993
DETAILED FLOW
1.
VISUAL INSPECTION
1.
Check battery case for cracks or bends.
2.
Check battery terminals for damage.
Are these inspection results normal?
YES
>> GO TO 2.
NO
>> Replace battery.
2.
CHECK BATTERY (USE CONSULT)
Check the battery, using CONSULT. Refer to
ECH-316, "Diagnosis Procedure"
(K9K), or
EC9-405, "Diagnosis Procedure"
(R9M).
Is the check result normal?
YES
>> GO TO 3.
NO
>> Replace battery.
3.
CAPACITY TEST
Check battery voltage.
Is the voltage 12.35 V or more?
YES
>> GO TO 4.
NO
>> GO TO 5.
4.
DISCHARGE
1.
Check battery type and determine the specified current using the table.
2.
Perform discharge using the load tester.
Is the voltage 10 V or more?
YES
>> Ready for use.
NO
>> Replace battery.
5.
CHARGE
Charge battery, following the instructions below:
• Constant current charging may damage batteries. Therefore, charge battery by constant voltage charge
mode with the maximum voltage set at 15 V.
• Charge at least 6 hours or until the charge current becomes 4 amps or less.
>> GO TO 4.
Type
Current (A)
L2
300
L3
300
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст