Isuzu Rodeo UE. Manual — part 296
6B–2
ENGINE COOLING (6VD1 3.2L)
General Description
030RW001
Legend
(1) Water Pump
(2) Thermostat
(3) Radiator
(4) Reserve Tank
(5) Cooling Fan
(6) Cylinder Block
(7) Cylinder Head
(8) Right Bank
(9) Throttle Body
(10) Cylinder Block
(11) Cylinder Head
(12) Left Bank
(13) Heater
The cooling system is a pressurized Engine Coolant (EC)
forced circulation type which consists of a water pump,
thermostat cooling fan, radiator and other components.
The automatic transmission fluid is cooled by the EC in
radiator.
Water Pump
The EC pump is a centrifugal impeller type and is driven
by a timing belt.
030RS001
ENGINE COOLING (6VD1 3.2L)
6B–3
Thermostat
The thermostat is a wax pellet type with a air hole(1) and is
installed in the thermostat housing.
031RW002
Radiator
The radiator is a tube type with corrugated fins. In order to
raise the boiling point of the coolant, the radiator is fitted
with a cap in which the valve is operated at 88.2
∼
117.6
kPa (12.8
∼
17.0 psi) pressure. (No oil cooler provided for
M/T)
110RW023
Antifreeze Solution
f
Relation between the mixing ratio and freezing
temperature of the EC varies with the ratio of
anti–freeze solution in water. Proper mixing ratio can
be determined by referring to the chart. Supplemental
inhibitors or additives claiming to increase cooling
capability that have not been specifically approved by
Isuzu are not recommended for addition to the cooling
system.
f
Calculating mixing ratio
F06RW005
NOTE: Antifreeze solution + Water = Total cooling
system capacity.
f
Total Cooling System Capacity
f
M/T 11.1Lit (2.93Us gal)
f
A/T 10.0Lit (2.64Us gal)
B06RW002
6B–4
ENGINE COOLING (6VD1 3.2L)
f
Mixing ratio
Check the specific gravity of engine coolant in the
cooling system temperature ranges from 0
°
C to 50
°
C
using a suction type hydrometer, then determine the
density of the engine coolant by referring to the table.
B06RW003
Diagnosis
Engine Cooling Trouble
Condition
Possible cause
Correction
Engine overheating
Low Engine Coolant level
Replenish
Incorrect fan installed
Replace
Thermo meter unit faulty
Replace
Faulty thermostat
Replace
Faulty Engine Coolant temperature
sensor
Repair or replace
Clogged radiator
Clean or replace
Faulty radiator cap
Replace
Low engine oil level or use of
improper engine oil
Replenish or change oil
Clogged exhaust system
Clean exhaust system or replace
faulty parts
Faulty Throttle Position sensor
Replace throttle valve assembly
Open or shorted Throttle Position
sensor circuit
Repair or replace
Damaged cylinder head gasket
Replace
Engine overcooling
Faulty thermostat
Replace
Engine slow to warm–up
Faulty thermostat
Replace
Thermo unit faulty
Replace
ENGINE COOLING (6VD1 3.2L)
6B–5
Draining and Refilling Cooling
System
Before draining the cooling system, inspect the system
and perform any necessary service to ensure that it is
clean, does not leak and is in proper working order. The
engine coolant (EC) level should be between the “MIN”
and “MAX” lines of reserve tank when the engine is cold.
If low, check for leakage and add EC up to the “MAX” line.
There should not be any excessive deposit of rust or
scales around the radiator cap or radiator filler hole, and
the EC should also be free from oil.
Replace the EC if excessively dirty.
1. Completely drain the cooling system by opening the
drain plug (2) at the bottom of the radiator.
110RW002
2. Remove the radiator cap.
WARNING: TO AVOID THE DANGER OF BEING
BURNED, DO NOT REMOVE THE CAP WHILE THE
ENGINE AND RADIATOR ARE STILL HOT.
SCALDING FLUID AND STEAM CAN BE BLOWN OUT
UNDER PRESSURE.
3. Disconnect all hoses from the EC reserve tank.
Scrub and clean the inside of the reserve tank with
soap and water. Flush it well with clean water, then
drain it. Install the reserve tank and hoses.
4. Refill the cooling system with the EC using a solution
that is at least 50 percent antifreeze but no more than
70 percent antifreeze.
5. Fill the radiator to the base of the filler neck.
Fill the EC reserve tank to “MAX” line when the engine
is cold.
6. Block the drive wheels and firmly apply the parking
brake. Shift an automatic transmission to “P” (Park)
or a manual transmission to neutral.
7. Remove the radiator cap. Start the engine and warm
it up at 2,500
∼
3,000 rpm for about 30 minutes.
8. When the air comes out from the radiator filler neck
and the EC level has gone down, replenish with the
EC. Repeat this procedure until the EC level does not
go down. Then stop the engine and install the radiator
cap. Let the engine cool down.
9. After the engine has cooled, replenish with EC up to
the “MAX” line of the reserve tank.
10. Start the engine. With the engine running at 3,000
rpm, make sure there is no running water sound from
the heater core (behind the center console).
11. If the running water sound is heard, repeat steps 8 to
10.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст