Daewoo Matiz (2003 year). Manual — part 17
![](/vehicles/epme/widy/zwanid/onayourinvei.png)
1E – 20 ENGINE ELECTRICAL
D102E704
D
Inspect the pinion gear’s moving to the outside (2).
D
If the pinion gear does not move outside, replace
the magnetic switch.
D102E705
4. Solenoid hold-in test.
D
Disconnect the starter motor terminal M (1).
D
Connect the 12-volt battery lead to the starter mo-
tor terminal S and body.
Notice: Complete the testing in a minimum amount of
time to prevent overheating and damaging the solenoid.
D102E706
D
Check the pinion gear’s moving to the outside (2).
D
If the pinion gear move to the inside, the circuit is
open. Replace the magnetic switch.
D102E707
5. Solenoid return test.
D
Disconnect the starter motor terminal M (1).
D
Connect the 12-volt battery lead to the starter mo-
tor terminal S and body.
Notice: Complete the testing in a minimum amount of
time to prevent overheating and damaging the solenoid.
![](/vehicles/epme/widy/zwanid/byoffon.png)
ENGINE ELECTRICAL 1E – 21
D102E708
D
Check the returning speed of pinion gear (2).
If the returning speed is fast, the operation is nor-
mal.
D
Replace the solenoid if the operation is abnormal.
D102E709
5. No-road test.
D
Connect the 12-volt battery lead to the starter cir-
cuit.
D
Connect the current and the voltage (1).
D
Install the starter motor rpm gage (2).
D
Start the starter motor with the switch on (3).
D
Measure the speed of pinion gear and the current.
D
If the measurement satisfy the limit, the starter mo-
tor is normal.
D102E710
Desciption
Limit
The speed of pinion
gear
Minimum: 2,000 rpm
Condition:
Voltage/Current
Maximum: 9V / 150A
D
Replace the starter motor if necessary.
D102E711
Disassembly Procedure
1. Remove the starter contact end frame.
D
Remove the through-bolts (1).
D
Remove the contact end frame bolts (2).
D
Remove the frame with the spacer (3).
![](/vehicles/epme/widy/zwanid/dnthe.png)
1E – 22 ENGINE ELECTRICAL
D102E712
2. Remove the brush holder assembly.
D
Remove the starter motor terminal M nut (1).
D
Remove the brush holder assembly (2).
D102E713
3. Remove the field frame assembly from the armature
set (1).
D102E714
4. Remove the solenoid assembly.
D
Remove the solenoid screws (1).
D
Remove the magnetic switch (2).
D
Remove the spring (3).
D102E715
5. Remove the armature set and solenoid from the start-
er housing.
D
Remove the armature set (1).
D
Remove the rubber sealer (2).
D
Remove the shift lever plate (3).
D
Remove the shift lever (4).
D
Remove the solenoid (5).
D
Remove the gasket (6).
![](/vehicles/epme/widy/zwanid/nen.png)
ENGINE ELECTRICAL 1E – 23
D102E716
Inspection / Measurement
(After the Overhaul)
1. Ground test for armature coil.
D
Inspect the insulation between commutator and ar-
mature coil using the voltmeter.
D
Replace the armature assembly if necessary.
D102E717
2. Short circuit test for armature coil.
D
If test equipment is available, check the armature
for short circuit by placing it on a growler, and hold-
ing back a saw blade over the armature core while
the armature is rotated. If the saw blade vibrates,
replace the armature.
D102E718
3. Open circuit test for armature coil.
D
Check the continuity between the commutator
bars using multimeter.
D
Replace the armature assembly if necessary.
D102E719
4. Inspect the brushes wear.
D
Inspect the brushes, the pop-out springs and the
brush holder for wear and damage. Replace the
brushes, if necessary.
a. Brushes wear limit.
Desciption
Standard
Limit
Brushes wear
11.3–11.5 mm
(0.445–0.453 in)
7.0–7.25 mm
(0.275–0.285 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст