Dacia Solenza (engine E7J). Manual — part 165
![](/vehicles/dyoifreyoodi/gularthrd/quthaser/vead.png)
87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 20
Diagnostic –States interpretation
Perform again a system diagnostic
Repair the other possible failures
Erase the memorized failures.
ET291
HAZARD LIGHTS INFORMATION
RECOMMENDATIONS
No failure must be present or memorized.
Act upon the hazard lights switch.
State must be
ACTIVE
ET291 INACTIVE
Check supply fuse
F13 (25A)
for turning / Cockpit Central Unit.
Replace it if necessary.
Check connection and condition of the hazard lights contact
connector
Repair the connector if necessary.
Check continuity of the connection:
Hazard lights contact pins 5 and 6 mass
Fix if necessary.
Check
insulation, continuity and absence of parasite resistance
of the connection:
Hazard lights contact pin 8 pin
B33
EH1 connector
with 40 pins
Fix if necessary.
Check operation of hazard lights control
AFTER REPARATION
![](/vehicles/dyoifreyoodi/gularthrd/quthaser/knis.png)
87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 21
ET309
ET310
RIGHT TURNING INFORMATION
LEFT TURNING INFORMATION
Diagnostic – States interpretation
No failure must be present or memorized.
RECOMMENDATIONS
Set on the contact
Act upon the left or right turning control
State must be ACTIVE
Check the supply fuse F13 (25A) for turning lights/Cockpit Central
Unit.
Replace it if necessary.
Check connection and condition of the turning switch connector.
Fix is necessary.
Ensure continuity of the connection:
Turning switch pin 6 mass
Fix if necessary
Disconnect connector EH1 40 pins of UCH
Ensure continuity and insulation of the connections:
Right turning switch pin 5
pin B28
connector
EH1 40 pins UCH
Left turning switch pin 7
pin B26
connector
EH1 40 pins UCH
Fix is necessary.
Perform again a system diagnostic
Repair the other possible failures
Erase the memorized failures.
AFTER REPARATION
ET309
ar
ET310
INACTIVE
![](/vehicles/dyoifreyoodi/gularthrd/quthaser/quth.png)
87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 22
Diagnostic – States interpretation
ET213
WINDSCREEN WIPER TIMER
RECOMMENDATIONS
No failure must be present or memorized.
Set on the contact
Act upon the left or right turning control
State must be ACTIVE
Check the windscreen wiper fuse F07 (20A).
Replace it if necessary.
Check the connection and condition of windscreen wiper switch connector
Fix the connector if necessary.
Ensure continuity and insulation of the connections:
connector EH1 of UCH
pin B24
wiper switch pin
A1
+ after contact wiper switch pin
A7
Fix if necessary.
ET213
INACTIVE
Perform again a system diagnostic
Repair the other possible failures
Erase the memorized failures.
AFTER REPARATION
![](/vehicles/dyoifreyoodi/gularthrd/quthaser/xthach.png)
87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 23
Diagnostic – States interpretation
ET192
FRONT DOORS
RECOMMENDATIONS Check that no failure is be present or memorized.
Open the drivers’ door
Check that for open door the corresponding state is active or for closed door, the
corresponding state is inactive
Check continuity and insulation of the wiring between:
Driver’s doors contact and pin 40B of UCH connector EH1
Fix if necessary (see electric diagram of that vehicle)
Open the door.
Check continuity between mass and pin 40B of UCH
Close the door and check that no continuity is between mass and pin 40B of UCH
In case of a failure, replace the driver’s door contact.
Perform again a system diagnostic
Repair the other possible failures
Erase the memorized failures.
AFTER REPARATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст