Chery Tiggo 5 (T21). Service manual — part 149
11–
15
11
Center Pipe Assembly
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Raise the vehicle to a proper height.
4. Remove the center pipe assembly.
a. Remove 2 coupling nuts (arrow), disconnect the
connection between main catalytic converter assembly
and center pipe assembly, and take off the gasket in
the connecting part.
(Tightening torque: 50 ± 5 N·m)
b. Remove 2 spring bolts (arrow), disconnect the
connection between center pipe assembly and muffler
assembly, and take off the sphere flange grommet in
the connecting part.
(Tightening torque: 50 ± 5 N·m)
WARNING
The temperature of exhaust system is very high when engine is running. Before removal, make sure that
engine has stopped running; otherwise, there is a risk of scald injury.
CAUTION
When removing center pipe assembly, an assistant is needed to hold center pipe assembly. Prevent
center pipe assembly from dropping to cause accidents during operation.
Be sure to wear necessary safety equipment to prevent accidents when repairing.
Try to prevent body paint surface from being scratched during removal and installation.
RT21110140
RT21110150
11–
16
11
c. Detach the diamond shaped hanger block (arrow)
between center pipe assembly and body hook.
d. Remove the center pipe assembly.
Installation
Installation is in the reverse order of removal.
RT21110160
CAUTION
If gasket is damaged, replace it, and remove foreign matter on joints and threads.
If sphere flange grommet is damaged, replace it, and remove foreign matter on joints and threads.
If there are cracks or leaks, replace the damaged parts.
During installation, check that exhaust system components do not contact with muffler heat insulator I or
vehicle underbody. Make sure that clearance between exhaust system components and muffler heat
insulator I or vehicle underbody is more than 25 mm.
Check for exhaust gas leaks. If gas leaks, tighten defective area to prevent leaking. Replace damaged
parts as necessary.
11–
17
11
Muffler Assembly
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Raise the vehicle to a proper height.
4. Remove the muffler assembly.
a. Remove 2 spring bolts (arrow), disconnect the
connection between muffler assembly and center pipe
assembly, and take off the sphere flange grommet in
the connecting part.
(Tightening torque: 50 ± 5 N·m)
b. Detach the diamond shaped hanger block (1)
between left side of muffler assembly and body hook.
c. Detach the hanger block III (2) between left side of
muffler assembly and body hook.
WARNING
The temperature of exhaust system is very high when engine is running. Before removal, make sure that
engine has stopped running, otherwise, there is a risk of scald injury.
CAUTION
When removing center pipe assembly, an assistant is needed to hold muffler assembly. Prevent muffler
assembly from dropping to cause accidents during operation.
Be sure to wear necessary safety equipment to prevent accidents when repairing.
Try to prevent body paint surface from being scratched during removal and installation.
RT21110150
1
2
RT21110170
11–
18
11
d. Detach the diamond shaped hanger block (1)
between right side of muffler assembly and body
hook.
e. Detach the hanger block III assembly (2) between
right side of muffler assembly and body hook.
f. Remove the muffler assembly.
5. Remove the hanger block III assembly.
a. Remove 2 fixing bolts (arrow) from hanger block III
assembly on the left side of muffler assembly.
(Tightening torque: 50 ± 5 N·m)
b. Remove the hanger block III assembly from the left
side of muffler assembly.
c. Remove 2 fixing bolts (arrow) from hanger block III
assembly on the right side of muffler assembly.
(Tightening torque: 50 ± 5 N·m)
d. Remove the hanger block III assembly from the right
side of muffler assembly.
6. Remove the muffler assembly heat insulator.
a. Remove 4 clamping pieces (1) from the muffler
assembly heat insulator I, and remove the muffler
assembly heat insulator I.
b. Remove 4 clamping pieces (2) from the muffler
assembly heat insulator II, and remove the muffler
assembly heat insulator II.
1
2
RT21110180
RT21110190
RT21110200
1
2
RT21110210
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст