Jaguar XJ (X350). Service manual — part 994
Is the resistance less than 10 ohms?
-> Yes
Suspect: - ECM connector - ECM
-> No
REPAIR the high resistance circuit. For additional information, refer to the wiring diagrams. Clear any
DTCs, test the system for normal operation.
G549822t39 : CHECK THE EOT SIGNAL CIRCUIT FOR SHORT CIRCUIT TO
GROUND
1. Measure the resistance between:
C28, harness side
Battery
Pin 01
Negative terminal
Is the resistance greater than 100 Kohms?
-> Yes
GO to Pinpoint Test G549822t40.
-> No
GO to Pinpoint Test G549822t43.
G549822t40 : CHECK THE EOT SIGNAL CIRCUIT FOR SHORT CIRCUIT TO
POWER
1. Measure the resistance between:
C28, harness side
Battery
Pin 01
Positive terminal
Is the resistance greater than 100 Kohms?
-> Yes
GO to Pinpoint Test G549822t41.
-> No
GO to Pinpoint Test G549822t46.
G549822t41 : CHECK THE EOT SIGNAL CIRCUIT FOR HIGH RESISTANCE
1. Key off. 2. Disconnect the ECM connector, C100. 3. Measure the resistance between:
C28, harness side C100, harness side
Pin 01
Pin A1
Is the resistance less than 10 ohms?
-> Yes
GO to Pinpoint Test G549822t42.
-> No
REPAIR the high resistance circuit. For additional information, refer to the wiring diagrams. Clear any
DTCs, test the system for normal operation.
G549822t42 : CHECK THE COMPONENT RESISTANCE
1. Measure the resistance between:
C28, component side C28, component side
Pin 01
Pin 02
Is the resistance between 1 - 500 Kohms?
-> Yes
An intermittent fault may be present in the wiring harness. Visually check for chaffed wires or other
physical damage to the harness. If no fault is found in the circuit, suspect the following
component(s): - EOT connector - EOT sensor - ECM connector - ECM
-> No
INSTALL a new EOT sensor. Clear any DTCs, test the system for normal operation.
G549822t43 : CHECK THE EOT SIGNAL AND RETURN CIRCUITS FOR SHORT
CIRCUIT TO EACH OTHER
1. Key off. 2. Disconnect the ECM connector, C100. 3. Key on, engine off. 4. Measure the resistance
between:
www.
C28, harness side C28, harness side
Pin 01
Pin 02
Is the resistance greater than 100 Kohms?
-> Yes
GO to Pinpoint Test G549822t44.
-> No
REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear any DTCs, test
the system for normal operation.
G549822t44 : CHECK WHETHER THE SHORT CIRCUIT TO GROUND IS IN THE
HARNESS OR THE MODULE
1. Measure the resistance between:
C28, harness side
Battery
Pin 01
Negative terminal
Is the resistance greater than 100 Kohms?
-> Yes
Suspect: - ECM
-> No
REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear any DTCs, test
the system for normal operation.
G549822t45 : CHECK WHETHER THE SHORT CIRCUIT TO POWER IS IN THE
HARNESS OR THE MODULE
1. Key off. 2. Disconnect the ECM connector, C100. 3. Key on, engine off. 4. Measure the resistance
between:
C28, harness side
Battery
Pin 02
Positive terminal
Is the resistance greater than 100 Kohms?
-> Yes
Suspect: - ECM
-> No
REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear any DTCs, test
the system for normal operation.
G549822t46 : CHECK WHETHER THE SHORT CIRCUIT TO POWER IS IN THE
HARNESS OR THE MODULE
1. Key off. 2. Disconnect the ECM connector, C100. 3. Key on, engine off. 4. Measure the resistance
between:
C28, harness side
Battery
Pin 01
Positive terminal
Is the resistance greater than 100 Kohms?
-> Yes
Suspect: - ECM
-> No
REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear any DTCs, test
the system for normal operation.
PINPOINT TEST G549822p4 :
ACCELERATOR PEDAL POSITION
(APP) SENSOR 1
G549822t47 : CHECK THE APP1 VALUE, WITH THE ACCELERATOR PEDAL
RELEASED
1.
www.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст