Jaguar XJ (X350). Service manual — part 1011
-> Yes
Suspect: - ECM connector - ECM
-> No
REPAIR the high resistance circuit. For additional information, refer to the wiring diagrams. Clear any
DTCs, test the system for normal operation.
G549822t173 : CHECK FOR POWER TO THE ACT SENSOR
1. Measure the voltage between:
C69, harness side
Battery
Pin 01
Negative terminal
Is the voltage between 4.8 - 5.2 volts?
-> Yes
GO to Pinpoint Test G549822t177.
-> No
GO to Pinpoint Test G549822t174.
G549822t174 : CHECK THE ACT SIGNAL CIRCUIT FOR SHORT CIRCUIT TO
GROUND
1. Measure the resistance between:
C69, harness side
Battery
Pin 01
Negative terminal
Is the resistance greater than 100 Kohms?
-> Yes
GO to Pinpoint Test G549822t175.
-> No
GO to Pinpoint Test G549822t178.
G549822t175 : CHECK THE ACT SIGNAL CIRCUIT FOR SHORT CIRCUIT TO
POWER
1. Key on, engine off. 2. Measure the resistance between:
C69, harness side
Battery
Pin 01
Positive terminal
Is the resistance greater than 100 Kohms?
-> Yes
GO to Pinpoint Test G549822t176.
-> No
GO to Pinpoint Test G549822t181.
G549822t176 : CHECK THE ACT SIGNAL CIRCUIT FOR HIGH RESISTANCE
1. Key off. 2. Disconnect the ECM connector, C101. 3. Measure the resistance between:
C69, harness side C101, harness side
Pin 01
Pin B1
Is the resistance less than 10 ohms?
-> Yes
Suspect: - ECM connector - ECM
-> No
REPAIR the high resistance circuit. For additional information, refer to the wiring diagrams. Clear any
DTCs, test the system for normal operation.
G549822t177 : CHECK THE COMPONENT RESISTANCE
1. Measure the resistance between:
C69, component side C69, component side
Pin 01
Pin 02
www.
Is the resistance between 1 - 100 Kohms?
-> Yes
An intermittent fault may be present in the wiring harness. Visually check for chaffed wires or other
physical damage to the harness. If no fault is found in the circuit, suspect the following
component(s): - ACT connector. - ACT sensor. - ECM connector. - ECM
-> No
INSTALL a new ACT sensor.
G549822t178 : CHECK THE ACT SIGNAL AND RETURN CIRCUITS FOR SHORT
CIRCUIT TO EACH OTHER
1. Key off. 2. Disconnect the ECM connector, C101. 3. Key on, engine off. 4. Measure the resistance
between:
C69, harness side C69, harness side
Pin 01
Pin 02
Is the resistance greater than 100 Kohms?
-> Yes
GO to Pinpoint Test G549822t179.
-> No
REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear any DTCs, test
the system for normal operation.
G549822t179 : CHECK WHETHER THE SHORT CIRCUIT TO GROUND IS IN
THE HARNESS OR THE MODULE
1. Key on, engine off. 2. Measure the resistance between:
C69, harness side
Battery
Pin 01
Negative terminal
Is the resistance greater than 100 Kohms?
-> Yes
Suspect: - ECM
-> No
REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear any DTCs, test
the system for normal operation.
G549822t180 : CHECK WHETHER THE SHORT CIRCUIT TO POWER IS IN THE
HARNESS OR THE MODULE
1. Key off. 2. Disconnect the ECM connector, C101. 3. Key on, engine off. 4. Measure the resistance
between:
C69, harness side
Battery
Pin 02
Positive terminal
Is the resistance greater than 100 Kohms?
-> Yes
Suspect: - ECM
-> No
REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear any DTCs, test
the system for normal operation.
G549822t181 : CHECK WHETHER THE SHORT CIRCUIT TO POWER IS IN THE
HARNESS OR THE MODULE
1. Key off. 2. Disconnect the ECM connector, C101. 3. Key on, engine off. 4. Measure the resistance
between:
C69, harness side
Battery
Pin 01
Positive terminal
Is the resistance greater than 100 Kohms?
-> Yes
Suspect: - ECM
-> No
REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear any DTCs, test
the system for normal operation.
www.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст