Jaguar XJ (X350). Service manual — part 941
-> Yes
REPAIR the high resistance circuit. For additional information, refer to the wiring diagrams. CLEAR the
DTC. TEST the system for normal operation.
-> No
INSTALL a new catalyst monitor sensor.
Catalyst Monitor Sensor (18.30.66) CLEAR the DTC. TEST the system for normal operation.
PINPOINT TEST G531332p9 : RIGHT-
HAND CATALYST MONITOR SENSOR
HEATER CONTROL CIRCUIT
LOW/HIGH RESISTANCE
G531332t31 : CHECK THE POWER SUPPLY TO THE CATALYST MONITOR
HEATER
1. Key off. 2. Disconnect the catalyst monitor sensor electrical connector, PI11. 3. Key on, engine off.
4. Make sure the O2S heater relay is engaged. 5. Measure the voltage between:
Catalyst monitor sensor connector PI11, harness side
Battery
Pin 02
Negative terminal
Is the voltage greater than 10 volts?
-> Yes
GO to Pinpoint Test G531332t32.
-> No
REPAIR the power supply circuit to the catalyst monitor sensor heater. This circuit includes the heater
relay and fuse 33 of the front power distribution box. For additional information, refer to the wiring
diagrams. CLEAR the DTC. TEST the system for normal operation.
G531332t32 : CHECK THE CATALYST MONITOR HEATER CONTROL CIRCUIT
FOR HIGH RESISTANCE
1. Key off. 2. Disconnect the ECM electrical connector, PI300. 3. Measure the resistance between:
Catalyst monitor sensor connector PI11, harness side ECM connector PI300, harness side
Pin 02
Pin 88
Is the resistance greater than 5 ohms?
-> Yes
REPAIR the high resistance circuit. For additional information, refer to the wiring diagrams. CLEAR the
DTC. TEST the system for normal operation.
-> No
INSTALL a new catalyst monitor sensor.
Catalyst Monitor Sensor (18.30.66) CLEAR the DTC. TEST the system for normal operation. If the DTC
is repeated, refer to the warranty policy and procedures manual if an ECM is suspect.
PINPOINT TEST G531332p10 : LEFT-
HAND H02S SENSING CIRCUIT
LOW/HIGH CURRENT, SLOW
RESPONSE, ECM CONTROL
MALFUNCTION
G531332t33 : CHECK THE H02S VARIABLE CIRCUIT FOR HIGH RESISTANCE
1. Key off. 2. Disconnect the H02S electrical connector, PI12. 3. Disconnect the ECM electrical
connector, PI300. 4. Measure the resistance between:
HO2S connector PI12, harness side ECM connector PI300, harness side
Pin 04
Pin 26
Is the resistance greater than 5 ohms?
-> Yes
REPAIR the high resistance circuit. For additional information, refer to the wiring diagrams. CLEAR the
DTC. TEST the system for normal operation.
-> No
GO to Pinpoint Test G531332t34.
www.
G531332t34 : CHECK THE H02S VARIABLE CIRCUIT FOR SHORT CIRCUIT TO
POWER
1. Key on, engine off. 2. Measure the voltage between:
HO2S connector PI12, harness side
Battery
Pin 04
Negative terminal
Is the voltage greater than 3 volts?
-> Yes
REPAIR the short circuit. For additional information, refer to the wiring diagrams. CLEAR the DTC.
TEST the system for normal operation.
-> No
GO to Pinpoint Test G531332t35.
G531332t35 : CHECK THE H02S VARIABLE CIRCUIT FOR SHORT CIRCUIT TO
GROUND
1. Key off. 2. Measure the resistance between:
HO2S connector PI12, harness side
Battery
Pin 04
Negative terminal
Is the resistance less than 10,000 ohms?
-> Yes
REPAIR the short circuit. For additional information, refer to the wiring diagrams. CLEAR the DTC.
TEST the system for normal operation.
-> No
GO to Pinpoint Test G531332t36.
G531332t36 : CHECK THE H02S CONSTANT CIRCUIT FOR HIGH RESISTANCE
1. Measure the resistance between:
HO2S connector PI12, harness side ECM connector PI300, harness side
Pin 03
Pin 27
Is the resistance greater than 5 ohms?
-> Yes
REPAIR the high resistance circuit. For additional information, refer to the wiring diagrams. CLEAR the
DTC. TEST the system for normal operation.
-> No
GO to Pinpoint Test G531332t37.
G531332t37 : CHECK THE H02S CONSTANT CIRCUIT FOR SHORT CIRCUIT
TO POWER
1. Measure the voltage between:
HO2S connector PI12, harness side
Battery
Pin 03
Negative terminal
Is the voltage greater than 3 volts?
-> Yes
REPAIR the short circuit. For additional information, refer to the wiring diagrams. CLEAR the DTC.
TEST the system for normal operation.
-> No
GO to Pinpoint Test G531332t38.
G531332t38 : CHECK THE H02S CONSTANT CIRCUIT FOR SHORT CIRCUIT
TO GROUND
1. Measure the resistance between:
HO2S connector PI12, harness side
Battery
Pin 03
Negative terminal
Is the resistance less than 10,000 ohms?
www.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст