Jaguar XJ (X350). Service manual — part 255
-> No
REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear the DTC, test
the system for normal operation by driving the vehicle at more than 20 kph (12.5 mph) for more than
3 minutes.
G531322t97 : CHECK THE WSS SIGNAL CIRCUIT FOR SHORT CIRCUIT TO
GROUND
1. Measure the resistance between:
CV006, harness side
Battery
Pin 02
Negative terminal
•
Is the resistance greater than 100 Kohms?
-> Yes
GO to Pinpoint Test
G531322t98
.
-> No
REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear the DTC, test
the system for normal operation by driving the vehicle at more than 20 kph (12.5 mph) for more than
3 minutes.
G531322t98 : CHECK THE WSS SIGNAL CIRCUIT FOR HIGH RESISTANCE
1. Measure the resistance between:
CV006, harness side EC030, harness side
Pin 02
Pin 36
•
Is the resistance less than 10 ohms?
-> Yes
GO to Pinpoint Test
G531322t99
.
-> No
REPAIR the high resistance circuit. For additional information, refer to the wiring diagrams. Clear the
DTC, test the system for normal operation by driving the vehicle at more than 20 kph (12.5 mph) for
more than 3 minutes.
G531322t99 : CHECK THE WSS SIGNAL AND RETURN CIRCUITS FOR SHORT
CIRCUIT TO EACH OTHER
1. Measure the resistance between:
CV006, harness side CV006, harness side
Pin 01
Pin 02
•
Is the resistance greater than 100 Kohms?
-> Yes
An intermittent fault may be present in the wiring harness. Visually check for chaffed wires or other
physical damage to the harness. If no fault is found in the harness, suspect the following
components: - WSS connector - WSS - ABS module connector - ABS module
-> No
REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear the DTC, test
the system for normal operation by driving the vehicle at more than 20 kph (12.5 mph) for more than
3 minutes.
PINPOINT TEST G531322p7 : RIGHT
HAND REAR WHEEL SPEED SENSOR
(WSS)
G531322t24 : CHECK THE WSS RETURN CIRCUIT FOR SHORT CIRCUIT TO
GROUND
1.
Circuit
Pin
WSS return 01
WSS signal
02
www.
2.
Circuit
Pin
Right hand rear WSS return 42
Right hand rear WSS signal
43
3. Key off. 4. Disconnect the WSS connector, CV008. 5. Disconnect the ABS module connector, EC030.
6. Key on engine off. 7. Measure the resistance between:
CV008, harness side
Battery
Pin 01
Negative terminal
•
Is the resistance greater than 100 Kohms?
-> Yes
GO to Pinpoint Test
G531322t100
.
-> No
REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear the DTC, test
the system for normal operation by driving the vehicle at more than 20 kph (12.5 mph) for more than
3 minutes.
G531322t100 : CHECK THE WSS RETURN CIRCUIT FOR SHORT CIRCUIT TO
POWER
1. Measure the resistance between:
CV008, harness side
Battery
Pin 01
Positive terminal
•
Is the resistance greater than 100 Kohms?
-> Yes
GO to Pinpoint Test
G531322t101
.
-> No
REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear the DTC, test
the system for normal operation by driving the vehicle at more than 20 kph (12.5 mph) for more than
3 minutes.
G531322t101 : CHECK THE WSS RETURN CIRCUIT FOR HIGH RESISTANCE
1. Measure the resistance between:
CV008, harness side EC030, harness side
Pin 01
Pin 42
•
Is the resistance less than 10 ohms?
-> Yes
GO to Pinpoint Test
G531322t102
.
-> No
REPAIR the high resistance circuit. For additional information, refer to the wiring diagrams. Clear the
DTC, test the system for normal operation by driving the vehicle at more than 20 kph (12.5 mph) for
more than 3 minutes.
G531322t102 : CHECK THE WSS SIGNAL CIRCUIT FOR SHORT CIRCUIT TO
POWER
1. Measure the resistance between:
CV008, harness side
Battery
Pin 02
Positive terminal
•
Is the resistance greater than 100 Kohms?
-> Yes
GO to Pinpoint Test
G531322t103
.
www.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст