Jaguar XK. Service manual — part 36
147
Convertible top
R
3. Insert the Allen key into the pump and
rotate counterclockwise
(approximately one turn).
4. Pull the tonneau release cable, until
fully extended. Close the luggage
compartment lid.
5. Fully open the tonneau panel. It will
self-support when fully opened.
6. From the left-hand side of the vehicle,
place your right hand down the side
of the folded convertible top. Ensure
that the bottom of the convertible top,
which includes the tension bow, is
securely held. Securely hold the
convertible top header assembly with
your left hand. With both hands pull
the whole of the convertible top up
and forward.
E91373
E91383
E91384
E91385
Convertible top
148
L
7. Ensure that the tension bow is fully
raised.
8. Supporting the tension bow, lower
the tonneau panel 1. Then lower the
tension bow 2 onto the tonneau
panel.
9. Remove the plug from the convertible
top header trim.
10. Support the front header. Insert the
Allen key into the header panel key
slot and turn clockwise until the top is
securely latched and resistance is
felt.
11. Return the Allen key to its stowed
position, refit the rear seat centre
section, luggage compartment vent
screen and the plug into the
convertible top header trim.
E91386
1
2
E91387
E91388
E91389
149
Convertible top
R
Message centre information
displays
Message
Warnin
g Light
Priority
Indicat
or
Meaning
HOOD NOT LATCHED
None
Red
The convertible roof is not latched,
check for security.
HOOD OUT OF POSITION
None
Amber
The convertible roof is not positioned
correctly. Open or close the convertible
roof again and check for correct
positioning.
LUGGAGE COVER OUT
OF POSITION
None
Amber The luggage separator is out of position
and should be checked. See OPENING
Convenience features
150
L
Convenience features
MEMORY FUNCTION
This facility enables the position of the
driver’s seat, steering column and
exterior rear-view mirrors to be
memorised and recalled. Three different
position sets can be entered into the
memory.
Setting a driving position
To store a driving position in the memory:
1. Adjust the seat, steering column and
exterior rear-view mirrors to the
desired positions.
2. In the door switch pack, push the M
memory button, A, and the red LED,
B, will illuminate for a five second
period.
3. While the red LED is illuminated, push
either button 1, 2 or 3 to memorise.
The LED will go out and a chime will
indicate that the setting procedure is
complete. Additionally, if the ignition
is on, the message centre will display
a message that the settings have
been saved.
To replace a memorised position
with a new position
Adjust the seat to the desired position,
perform steps 2 and 3. The previous
memory will be erased and the new
position will be set.
Recalling a memorised position
from the door switchpack
Press and hold the appropriate memory
button (1, 2 or 3). The button has to be
pressed and remain pressed until the
recall is complete. If the button is
released before total recall is completed,
all movement will cease.
Memory system operating tips
• When making adjustments to a set
driving position, reset the new
position using the same memory
button.
• Ensure that the seat has completed
moving into the required memory
position before shifting the gear
selector from the P position.
Passenger seat memory setting
The passenger door has a seat memory
switch pack similar to that on the driver’s
door.
The passenger seat can be set to three
memory positions by using the memory
setting buttons 1, 2 and 3.
The procedure for the setting and the
recalling of the passenger seat memory is
the same as for the driver’s seat.
However, there are no acceptance
messages or a completed procedure
chime.
E91398
B
A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст