Toyota FJ Cruiser (GSJ 10, 15 series). Manual — part 328
![](/vehicle/ure/zyo/ppanger/rdom.png)
ME–44
METER – METER / GAUGE SYSTEM
ME
OK
(a) Connect the intelligent tester to the DLC3.
(b) Turn the ignition switch ON and the tester ON.
(c) Select the item below from the Data List, and read the
value displayed on the intelligent tester.
METER
OK:
Vehicle speed displayed on the tester is
approximately the same as the actual vehicle
speed.
NG
OK
(a) Disconnect the E13 combination meter assembly
connector.
(b) Disconnect the A4 skid control ECU connector.
REPLACE COMBINATION METER ASSEMBLY
5
READ VALUE OF INTELLIGENT TESTER (SPEED METER)
Item
Measurement Item /
Range(Display)
Normal Condition
Diagnostic Note
SPEED METER
Vehicle speed / Min.: 0 mph (0
km/h), Max.: 158mph (255 km/
h)
Approximately same as actual
vehicle speed (When vehicle is
driven)
-
GO TO BRAKE SYSTEM
6
CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER
ASSEMBLY)
![](/vehicle/ure/zyo/ppanger/udrase.png)
METER – METER / GAUGE SYSTEM
ME–45
ME
(c) Measure the resistance.
Standard resistance
NG
OK
31
32
2
1
3
4
5
6
7
8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30
33 34 35 36 37 38 39 40 41 42 43 44 45 46
Wire Harness Side:
SP1
GND2
A4
Skid Control ECU Connector
Front View
Combination Meter Assembly Connector
E13
SI
Front View
E126869E01
Tester Connection
Specified Condition
E13-E13 (SI) - A4-12 (SP1)
Below 1
Ω
A4-32 (GND2) - Body ground
Below 1
Ω
REPAIR OR REPLACE HARNESS OR
CONNECTOR
REPLACE COMBINATION METER ASSEMBLY
![](/vehicle/ure/zyo/ppanger/ibbraueaco.png)
ME–46
METER – METER / GAUGE SYSTEM
ME
DESCRIPTION
The combination meter assembly controls the tachometer in accordance with engine speed signals from
the ECM.
WIRING DIAGRAM
INSPECTION PROCEDURE
(a) Connect the intelligent tester to the DLC3.
(b) Turn the ignition switch ON and turn the tester ON.
(c) Select the item below from the Data List, and read the
value displayed on the intelligent tester.
METER
OK:
Engine speed displayed on the tester is
approximately the same as the actual engine
speed.
NG
OK
Tachometer Malfunction
1
READ VALUE OF INTELLIGENT TESTER (TACHOMETER)
Combination Meter Assembly (Tachometer)
ECM
S
TACH
E126870E01
Item
Measurement Item/Range
(Display)
Normal Condition
Diagnostic Note
TACHOMETER
Engine speed/Min.: 0 rpm,
Max.: 12,750 rpm
Approximately same as actual
engine speed (When engine is
running)
-
GO TO SFI SYSTEM
![](/vehicle/ure/zyo/ppanger/ndonine.png)
METER – METER / GAUGE SYSTEM
ME–47
ME
(a) Disconnect the E13 combination meter connector.
(b) Disconnect the E46 ECM connector.
(c) Measure the resistance.
Standard resistance
(d) Reconnect the ECM connector.
(e) Reconnect the combination meter connector.
NG
OK
2
CHECK WIRE HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
16
32
31
35
28
20
17
9 10
34
11
6
5
13 14 15
23 24
26
12
3
2
1
4
27
29
18
7
30
19
8
21 22
25
33
Wire Harness Side:
Front View:
E13
S
Front View:
Combination Meter Assembly Connector
ECM Connector
TACH
E46
E126864E01
Tester Connection
Specified Condition
E13-12 (S) - E46-1 (TACH)
Below 1
Ω
E13-12 (S) or E46-1 (TACH) - Body
ground
10 k
Ω or higher
REPAIR OR REPLACE HARNESS OR
CONNECTOR
REPLACE COMBINATION METER ASSEMBLY
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст