Toyota FJ Cruiser (GSJ 10, 15 series). Manual — part 130

ENGINE HOOD / DOOR – FRONT DOOR

ED–17

ED

2.

ADJUST FRONT DOOR
(a) Disconnect the cable from the negative battery

terminal.
CAUTION:
The work must be started at least 90 seconds
after the ignition switch is turned to OFF and the
cable is disconnected from the negative battery
terminal. (The SRS is equipped with a back-up
power source. If the work is started within 90
seconds of disconnecting the cable from the
negative battery terminal and the ignition switch
being turned to OFF, the SRS may deploy).

(b) Apply strips of protective tape to the door panel and

fender panel, as shown in the illustration.

(c) Open the door, and then disengage the 5 clips.

HINT:
If any clips are damaged, replace them with new
ones.

(d) Remove the front fender splash shield from the gap

between the fender and door.

(e) Using SST, adjust the door horizontally and

vertically by loosening the body side hinge bolts.
SST

09812-00010

(f)

Tighten the body side hinge bolts after the
adjustment.
Torque: 26 N*m (265 kgf*cm, 19 ft.*lbf)

Protective Tape

B135985E01

B135986

SST

B135987E01

ED–18

ENGINE HOOD / DOOR – FRONT DOOR

ED

(g) Adjust the door horizontally and vertically by

loosening the door side hinge bolts.

(h) Tighten the door side hinge bolts after the

adjustment.
Torque: 26 N*m (265 kgf*cm, 19 ft.*lbf)

(i)

Using "Torx" socket wrench T40, adjust the striker
position by slightly loosening the striker mounting
screws and hitting the striker with a plastic-faced
hammer.

(j)

Using "Torx" socket wrench T40, tighten the striker
mounting screws after the adjustment.
Torque: 23 N*m (235 kgf*cm, 17 ft.*lbf)

(k) Install the front fender splash shield with the 5 clips.
(l)

Connect the cable to the negative battery terminal.
Torque: 3.9 N*m (40 kgf*cm, 35 in.*lbf)

REASSEMBLY

1.

INSTALL CUSHION
(a) Install the 2 cushions.

2.

INSTALL FRONT DOOR OUTSIDE MOULDING SUB-
ASSEMBLY
HINT:
Use the same procedure as for the LH side (see page

ET-75

).

B135988

B135989

B135986

B135587

ENGINE HOOD / DOOR – FRONT DOOR

ED–19

ED

3.

INSTALL FRONT DOOR OUTSIDE HANDLE FRAME
SUB-ASSEMBLY
(a) Using "Torx" socket wrench T30, install the front

door outside handle frame with the screw.
Torque: 7.0 N*m (71 kgf*cm, 62 in.*lbf)
NOTICE:
A cover should be inserted between the nut and
the door panel.

4.

INSTALL FRONT DOOR OUTSIDE HANDLE FRONT
PAD
(a) Engage the 3 claws and install the front door outside

handle front pad.

5.

INSTALL FRONT DOOR OUTSIDE HANDLE REAR
PAD
(a) Engage the 2 claws and install the front door outside

handle rear pad.

6.

INSTALL FRONT DOOR OUTSIDE HANDLE
ASSEMBLY
(a) While pushing the front door outside handle in the

direction of the arrow mark shown in the illustration,
install the front door outside handle.

7.

INSTALL FRONT DOOR LOCK (See page

DL-112

)

Slide

Screw

Frame

Nut

Door
Panel

Outside:

Inside:

Slide

B135586E01

B135584

B135583

B135581

ED–20

ENGINE HOOD / DOOR – FRONT DOOR

ED

8.

INSTALL FRONT DOOR OUTSIDE HANDLE COVER
(a) Engage the 2 claws and install the front door outside

handle cover.

(b) Using "Torx" socket wrench T30, install the cover

with the door lock key cylinder.
Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)
HINT:
Make sure that the door lock key cylinder rod is
inserted.

(c) Install the hole plug.

9.

INSTALL POWER WINDOW REGULATOR MOTOR
ASSEMBLY (See page

WS-35

)

10. INSTALL FRONT DOOR WINDOW REGULATOR SUB-

ASSEMBLY
(a) Apply MP grease to the sliding and rotating areas of

the front door window regulator.
NOTICE:
Do not apply grease to the window regulator
spring.

(b) Install the front door window regulator with the 6

bolts.
Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf)
NOTICE:
Do not drop the window regulator as it may be
damaged.

(c) Connect the connector.

11. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

(a) Install the front door glass onto the front door

window regulator with the 2 bolts.
Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf)
NOTICE:
Do not damage the glass.

B135597

B135582

B135598

B138164