Lexus ES300 (1997 year). Service manual — part 360
![](/vehicle/tus/iorssayongal/foue/jwinou.png)
W03875
AB0119
F00256
STP
ON
(–)
(+)
–
DIAGNOSTICS
ELECTRIC MODULATED SUSPENSION
DI–217
369
1997 LEXUS ES300 (RM511U)
2
Check voltage between terminal STP of absorber control ECU connector and
body ground.
PREPARATION:
(a)
Remove the No.1 lower panel (See page
).
(b)
Turn the ignition switch ON.
CHECK:
Measure voltage between terminal STP of absorber control
ECU connector and body ground when brake pedal is released
and depressed.
OK:
Released
10 – 14 V
Depressed
Below 1.5 V
OK
Proceed to next circuit inspection shown on
problem symptoms table (See page
NG
3
Check harness and connectors between absorber control ECU and stop light
switch (See page
).
NG
Repair or replace harness or connector.
OK
Check and replace absorber control ECU.
![](/vehicle/tus/iorssayongal/foue/gangho.png)
W03893
J15
Absorber Control ECU
Absorber Control Switch
W–B
Connector
A
A
II
1
4
2
V
Y
A24
A24
SW2
SW1
3
21
W–B
Junction
DI–218
–
DIAGNOSTICS
ELECTRIC MODULATED SUSPENSION
370
1997 LEXUS ES300 (RM511U)
DTC
52
Absorber Control Switch Circuit
CIRCUIT DESCRIPTION
DTC No.
DTC Detecting Condition
Trouble Area
52
SW1 and SW2 of absorber control switch signal do not
change.
Absorber control switch
Open or short circuit in between absorber control switch and
absorber control ECU
Absorber control ECU
WIRING DIAGRAM
DI0AO–01
![](/vehicle/tus/iorssayongal/foue/ineveloe.png)
W03876
AB0119
F00257
SW1
ON
(–)
(+)
SW2
W04329
2
3
4
1
–
DIAGNOSTICS
ELECTRIC MODULATED SUSPENSION
DI–219
371
1997 LEXUS ES300 (RM511U)
INSPECTION PROCEDURE
1
Check voltage between terminals SW1 and SW2 of absorber control ECU con-
nector and body ground.
PREPARATION:
(a)
Remove the No.1 lower panel (See page
).
(b)
Using SST, connect between terminals Ts and E1 of
DLC1.
SST
09843–18020
(c)
Turn the ignition switch ON.
CHECK:
Measure voltage between terminals SW1 and SW2 of absorber
control ECU connector and body ground when move slowly
moving the absorber control switch ”COMFROT”
↔
”SPORT”
both ways one.
OK:
SW1:
Absorber control switch 1
8 V or more
Absorber control switch 2
Below 1.5 V
SW2:
Absorber control switch 3
8 V or more
Absorber control switch 4
Below 1.5 V
OK
Proceed to next circuit inspection shown on
problem symptoms table (See page
NG
![](/vehicle/tus/iorssayongal/foue/cel.png)
W03877
1
3
2
1
2
3
DI–220
–
DIAGNOSTICS
ELECTRIC MODULATED SUSPENSION
372
1997 LEXUS ES300 (RM511U)
2
Check absorber control switch.
PREPARATION:
(a)
Remove the upper control panel (See page
).
(b)
Disconnect the absorber control switch connector.
CHECK:
Check continuity between each terminal of absorber control
switch when each switch position.
OK:
Absorber control switch 3:
Terminals 2 and 3
Continuity
Absorber control switch 2:
Terminals 1 and 2
Continuity
Terminals 2 and 3
Continuity
Absorber control switch 1:
Terminals 1 and 2
Continuity
NG
Replace absorber control switch.
OK
3
Check harness and connectors between absorber control ECU and absorber
control switch and body ground (See page
NG
Repair or replace harness or connector.
OK
Check and replace absorber control ECU.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст