Nissan Juke F15. Instruction — part 126
![](/vehicle/qul/yoniol/zyent/eni.png)
C1116 STOP LAMP SWITCH
BRC-95
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
C1116 STOP LAMP SWITCH
DTC Logic
INFOID:0000000012199694
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF, and wait 10 seconds or more.
2. Start the engine.
NOTE:
Stop the vehicle.
3. Wait 1 minute or more.
NOTE:
Never depress brake pedal.
4. Depress brake pedal by 100 mm (3.94 in) or more, and maintain at that position for a minimum of 1 minute
or more.
5. Release brake pedal, and wait 1 minute or more.
6. Repeat step 4 to 5 ten or more times.
7. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
8. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
9. Perform self-diagnosis for “ABS”.
Is DTC “C1116” detected?
YES-1 >> “CRNT” is displayed: Proceed to
.
YES-2 >> “PAST” is displayed: INSPECTION END (Erase the memory of self-diagnosis results.)
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
NO-2 >> Confirmation after repair: INSPECTION END
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1116
STOP LAMP SW
(Stop lamp switch)
When stop lamp switch signal is not input when brake pedal operates.
PAST DTC
CRNT DTC
• Harness or connector
• Stop lamp switch signal circuit
• Harness or connector
• Stop lamp switch
• ABS actuator and electric unit (control unit)
• ABS actuator and electric unit (control unit) power supply sys-
tem
• Fuse
• Fusible link
• Battery
![](/vehicle/qul/yoniol/zyent/realdunt.png)
BRC-96
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC]
C1116 STOP LAMP SWITCH
Diagnosis Procedure
INFOID:0000000012199695
NOTE:
DTC “C1116” may be detected when the brake pedal and the accelerator pedal are simultaneously depressed
for 1 minute or more while driving the vehicle. This is not a malfunction.
1.
INTERVIEW FROM THE CUSTOMER
Check if the brake pedal and the accelerator pedal are simultaneously depressed for 1 minute or more while
driving the vehicle.
Is there such a history?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
PERFORM SELF-DIAGNOSIS
With
CONSULT
1. Erase self-diagnosis result for “ABS”.
2. Turn the ignition switch OFF
→ ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine.
NOTE:
Stop the vehicle.
4. Depress the brake pedal several times.
5. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
6. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
7. Perform self-diagnosis for “ABS”.
Is DTC “C1116” detected?
YES
>> GO TO 3.
NO
>> INSPECTION END
3.
STOP LAMP FOR ILLUMINATION
Depress brake pedal and check that stop lamp turns ON.
Does stop lamp turn ON?
YES
>> GO TO 5.
NO
>> Check the stop lamp system circuit. GO TO 4.
4.
CHECK DATA MONITOR (1)
With
CONSULT
1. Erase self-diagnosis result for “ABS”.
2. Turn the ignition switch OFF
→ ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine.
NOTE:
Stop the vehicle.
4. Select “ABS”, “DATA MONITOR” and “STOP LAMP SW” according to this order. Check that data monitor
displays “On” or “Off” when brake pedal is depressed or released. Refer to
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 5.
5.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
3. Check the stop lamp switch harness connector for disconnection or looseness.
![](/vehicle/qul/yoniol/zyent/nysct.png)
C1116 STOP LAMP SWITCH
BRC-97
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair / replace harness or connector, and GO TO 6.
6.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair / replace harness, connector, fuse, or fusible link.
7.
CHECK STOP LAMP SWITCH CLEARANCE
1. Turn the ignition switch OFF.
2. Check the stop lamp switch clearance. Refer to
BR-9, "Inspection and Adjustment"
.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Adjust stop lamp switch clearance. Refer to
BR-9, "Inspection and Adjustment"
. GO TO 8.
8.
CHECK DATA MONITOR (2)
With
CONSULT
1. Erase self-diagnosis result for “ABS”.
2. Turn the ignition switch OFF
→ ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine.
NOTE:
Stop the vehicle.
4. Select “ABS”, “DATA MONITOR” and “STOP LAMP SW” according to this order. Check that data monitor
displays “On” or “Off” when brake pedal is depressed or released. Refer to
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 9.
9.
CHECK STOP LAMP SWITCH
Check the stop lamp switch. Refer to
BRC-99, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Replace the stop lamp switch. Refer to
BR-20, "Removal and Installation"
. GO TO 10.
10.
CHECK DATA MONITOR (3)
With
CONSULT
1. Erase self-diagnosis result for “ABS”.
2. Turn the ignition switch OFF
→ ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine.
NOTE:
Start the vehicle.
4. Select “ABS”, “DATA MONITOR” and “STOP LAMP SW” according to this order. Check that data monitor
displays “On” or “Off” when brake pedal is depressed or released. Refer to
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 11.
11.
CHECK CONNECTOR AND TERMINAL
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector.
![](/vehicle/qul/yoniol/zyent/set.png)
BRC-98
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC]
C1116 STOP LAMP SWITCH
3. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
4. Check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with
harness connector.
5. Disconnect stop lamp switch harness connector.
6. Check the stop lamp switch harness connector for disconnection or looseness.
7. Check the stop lamp switch pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> Repair / replace harness, connector, or terminal, and GO TO 12.
12.
CHECK DATA MONITOR (4)
With
CONSULT
1. Connect ABS actuator and electric unit (control unit) harness connector.
2. Connect stop lamp switch harness connector.
3. Erase self-diagnosis result for “ABS”.
4. Turn the ignition switch OFF
→ ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
5. Start the engine.
NOTE:
Stop the vehicle.
6. Select “ABS”, “DATA MONITOR” and “STOP LAMP SW” according to this order. Check that data monitor
displays “On” or “Off” when brake pedal is depressed or released. Refer to
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 13.
13.
CHECK STOP LAMP SWITCH CIRCUIT (1)
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector.
3. Check the voltage between ABS actuator and electric unit (control unit) harness connector and ground.
Is the inspection result normal?
YES
>> Replace the ABS actuator and electric unit (control unit). Refer to
.
NO
>> Repair / replace harness or connector, and GO TO 14.
14.
CHECK STOP LAMP SWITCH CIRCUIT (2)
1. Turn the ignition switch OFF.
2. Disconnect stop lamp switch harness connector.
3. Check the continuity between ABS actuator and electric unit (control unit) harness connector and stop
lamp switch harness connector.
*1: Models with CVT
*2: Models with M/T
4. Check the continuity between ABS actuator and electric unit (control unit) harness connector and the
ground.
+
−
Condition
Voltage
ABS actuator and electric unit (control unit)
Connector
Terminal
E35
8
Ground
Brake pedal depressed
10
− 16 V
Brake pedal not depressed
Approx. 0 V
ABS actuator and electric unit (control unit)
Stop lamp switch
Continuity
Connector
Terminal
Connector
Terminal
E35
8
E102
*1
E118
*2
2
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст