Nissan Murano Z51. Instruction — part 1297
DRIVER AIR BAG MODULE
SR-13
< REMOVAL AND INSTALLATION >
[FOR USA AND CANADA]
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• Tighten the TORX bolts after completely adjusting the centers of fixing holes on the driver air bag
module side and the steering wheel side. If the holes are misaligned, the bolt threads are damaged
and the module is not installed securely.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
SR-14
< REMOVAL AND INSTALLATION >
[FOR USA AND CANADA]
SPIRAL CABLE
SPIRAL CABLE
Exploded View
INFOID:0000000005518905
Removal and Installation
INFOID:0000000005518906
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use the air tools or electric tools for servicing.
REMOVAL
1.
Remove the driver air bag module. Refer to
SR-11, "Removal and Installation"
.
2.
Remove the steering wheel. Refer to
ST-17, "Removal and Installation"
3.
Remove the steering column cover (upper/lower). Refer to
.
4.
Disconnect the spiral cable body side harness connectors (A).
NOTE:
Disconnect the spiral cable body side harness connectors after
removing the spiral cable.
5.
Remove the spiral cable fixing screws.
1.
Steering column cover (upper)
2.
Spiral cable
3.
Steering column cover (lower)
4.
Steering column assembly
A.
Driver air bag harness connector
JMHIA0506ZZ
JMHIA0507ZZ
SPIRAL CABLE
SR-15
< REMOVAL AND INSTALLATION >
[FOR USA AND CANADA]
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
6.
Remove the spiral cable side pawls (A).
7.
Pull out forward the spiral cable.
CAUTION:
• Never impact the spiral cable.
• Never impact the spiral cable by dropping, etc. Replace the
spiral cable if it has been dropped or sustained an impact.
• Never disassemble the spiral cable.
• Never apply lubricant to the spiral cable.
• Never allow oil, grease, detergent, or water to come in contact with the spiral cable.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• The spiral cable may snap during steering operation if the
cable is installed in an improper position.
The neutral position is set as per the following.
• Turn carefully the spiral cable clockwise to the end position.
Then turn it counterclockwise (about 2 and a half turns) and
stop turning at the mark (B) on which the stopper insertion
holes are in the same position.
• The service part is installed in the neutral position by the
stopper and can be set without adjusting after the stopper is
removed.
• Never over turn the spiral cable or go beyond number of turns
required. (This will cause the cable to snap.)
• Adjust the spiral cable locating pin (A) to the steering wheel
locating pin hole (C).
JMHIA0508ZZ
JMHIA0009ZZ
JMHIA0657ZZ
SR-16
< REMOVAL AND INSTALLATION >
[FOR USA AND CANADA]
SPIRAL CABLE
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст