Nissan Murano Z51. Instruction — part 1370
SRC-250
< DTC/CIRCUIT DIAGNOSIS >
[FOR MEXICO]
B1115, B1116 SATELLITE SENS RH
B1115, B1116 SATELLITE SENS RH
Description
INFOID:0000000005513796
DTC B1115, B1116 [COMM FAIL] SATELLITE SENS RH
Main “G” sensor generates signal voltage, when it detects deceleration beyond the specified level by vehicle
side collision.
OPERATION
When ACU defines both signal voltage of the “G” sensor and the Safing algorithm to be that of collision which
exceeds specified level, the driving circuit switches on and feeds the electric ignitor of both the front side air
bag and side curtain air bag.
STRUCTURE
Integrated type of the G sensor element for side collision with output terminals for signal voltage.
INSTALLATION
RH satellite sensor is installed at the underside of center pillar with fixed nuts.
DTC Logic
INFOID:0000000005513797
DTC DETECTION LOGIC
With CONSULT-lll
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.
CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
Is malfunctioning part detected?
YES
>> Refer to
SRC-251, "Diagnosis Procedure"
NO
>> INSPECTION END.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1115
B1116
SATELLITE SENS RH
[COMM FAIL]
[UNMATCH]
RH satellite sensor is out of order
• Disconnection of wiring harness
• Internal breakdown in RH satellite
sensor
• Internal breakdown in air bag diag-
nosis sensor unit
B1115, B1116 SATELLITE SENS RH
SRC-251
< DTC/CIRCUIT DIAGNOSIS >
[FOR MEXICO]
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
2.
CHECK AIR BAG WARNING LAMP
Check the air bag warning lamp status.
Is malfunctioning part detected?
YES
>> Refer to warning lamp flash code chart.
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000005513798
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace wiring harness.
3.
CHECK SATELLITE SENSOR
1.
Replace RH satellite sensor.
2.
Check the screen of CONSULT-lll.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Check the intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
SRC-252
< DTC/CIRCUIT DIAGNOSIS >
[FOR MEXICO]
B1118, B1119 SATELLITE SENS LH
B1118, B1119 SATELLITE SENS LH
Description
INFOID:0000000005513799
DTC B1118, B1119 [UNIT FAIL] SATELLITE SENS LH
Main “G” sensor generates signal voltage, when it detects deceleration beyond the specified level by vehicle
side collision.
OPERATION
When ACU defines both signal voltage of the “G” sensor and the Safing algorithm to be that of collision which
exceeds specified level, the driving circuit switches on and feeds the electric ignitor of both the front side air
bag and side curtain air bag.
STRUCTURE
Integrated type of the G sensor element for side collision with output terminals for signal voltage.
INSTALLATION
LH satellite sensor is installed at the underside of center pillar with fixed nuts.
DTC Logic
INFOID:0000000005513800
DTC DETECTION LOGIC
With CONSULT-lll
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.
CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
Is malfunctioning part detected?
YES
>> Refer to
SRC-253, "Diagnosis Procedure"
NO
>> INSPECTION END.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1118
B1119
SATELLITE SENS LH
[UNIT FAIL]
LH satellite sensor is out of order
• Disconnection of wiring harness
• Internal breakdown in LH satellite
sensor
• Internal breakdown in air bag diag-
nosis sensor unit
B1118, B1119 SATELLITE SENS LH
SRC-253
< DTC/CIRCUIT DIAGNOSIS >
[FOR MEXICO]
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
2.
CHECK AIR BAG WARNING LAMP
Check the air bag warning lamp status.
Is malfunctioning part detected?
YES
>> Refer to warning lamp flash code chart.
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000005513801
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace wiring harness.
3.
CHECK SATELLITE SENSOR
1.
Replace LH satellite sensor.
2.
Check the screen of CONSULT-lll.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Check the intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст