Nissan Murano Z51. Instruction — part 635
EM-12
< PRECAUTION >
PRECAUTIONS
• As for bolt holes, normally apply liquid gasket inside the holes.
Occasionally, it should be applied outside the holes. Check to
read the text of this instruction.
• Within 5 minutes of liquid gasket application, install the mating
component.
• If liquid gasket protrudes, wipe it off immediately.
• Never retighten mounting bolts or nuts after the installation.
• After 30 minutes or more have passed from the installation, fill
engine oil and engine coolant.
CAUTION:
If there are specific instructions in this instruction, observe
them.
SEM159F
PREPARATION
EM-13
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000005515912
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
KV10116200
(J-26336-A)
Valve spring compressor
1. KV10115900
(J-26336-20)
Attachment
2. KV10109220
(
—
)
Adapter
Disassembling valve mechanism
Part (1) is a component of KV10116200 (J-
26336-A), but Part (2) is not so.
KV10107902
(J-38959)
Valve oil seal puller
Replacing valve oil seal
KV10115600
(J-38958)
Valve oil seal drift
Installing valve oil seal
Use side A.
a: 20 mm (0.79 in) dia.
b: 13 mm (0.51 in) dia.
c: 10.3 mm (0.406 in) dia.
d: 8 mm (0.31 in) dia.
e: 10.7 mm (0.421 in)
f: 5 mm (0.20 in)
EM03470000
(J-8037)
Piston ring compressor
Installing piston assembly into cylinder bore
ST16610001
(J-23907)
Pilot bushing puller
Removing pilot converter
KV10111100
(J-37228)
Seal cutter
Removing oil pan (lower and upper), front and
rear timing chain case, etc.
PBIC1650E
NT011
S-NT603
NT044
NT045
NT046
EM-14
< PREPARATION >
PREPARATION
Commercial Service Tool
INFOID:0000000005515913
KV10112100
(BT8653-A)
Angle wrench
Tightening bolts for connecting rod bearing
cap, cylinder head, etc. in angle
KV10117100
(J-3647-A)
Heated oxygen sensor wrench
Loosening or tightening air fuel ratio sensor 1
For 22 mm (0.87 in) width hexagon nut
KV10114400
(J-38365)
Heated oxygen sensor wrench
Loosening or tightening heated oxygen sen-
sor 2
a: 22 mm (0.87 in)
Tool number
(Kent-Moore No.)
Tool name
Description
NT014
NT379
NT636
(Kent-Moore No.)
Tool name
Description
(J-45488)
Quick connector release
Removing fuel tube quick connectors in en-
gine room
(
—
)
Power tool
Loosening bolts and nuts
(
—
)
Tube presser
Pressing the tube of liquid gasket
PBIC0198E
PBIC0190E
NT052
PREPARATION
EM-15
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
(
—
)
Instruction lift table caddy
Removing and installing engine
(J-24239-01)
Cylinder head bolt wrench
Loosening and tightening cylinder head bolt,
and used with the angle wrench [SST:
KV10112100 (BT8653-A)]
a: 13 mm (0.51 in) dia.
b: 12 mm (0.47 in)
c: 10 mm (0.39 in)
(
—
)
1. Compression tester
2. Adapter
Checking compression pressure
(
—
)
Spark plug wrench
Removing and installing spark plug
a: 14 mm (0.55 in)
(
—
)
Pulley holder
Removing and installing crankshaft pulley
(
—
)
Valve seat cutter set
Finishing valve seat dimensions
(
—
)
Piston ring expander
Removing and installing piston ring
(Kent-Moore No.)
Tool name
Description
ZZA1210D
NT583
ZZA0008D
JPBIA0399ZZ
ZZA1010D
NT048
NT030
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст