Nissan Murano Z51. Instruction — part 1373
SRC-262
< DTC/CIRCUIT DIAGNOSIS >
[FOR MEXICO]
B1131 SIDE MODULE RH
B1131 SIDE MODULE RH
Description
INFOID:0000000005513814
DTC B1131 [GND-SHORT] SIDE MODULE RH
For front RH side air bag module, crash is judged by main “G” sensor output signal (left side:LH satellite sen-
sor, right side:RH satellite sensor) and Safing algorithm (in air bag diagnosis sensor unit).
OPERATION
In the case of a collision whose acceleration exceeds the specified level, the ignition materials are ignited by
electric ignition system. The system burns and introduces the chemical reaction of gas generating materials to
generate hot gases that flow into the air bag through a filter and expand the bag.
STRUCTURE
Front RH side air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION
Front RH side air bag module is installed on the side of front seatback with fixed nuts.
DTC Logic
INFOID:0000000005513815
DTC DETECTION LOGIC
With CONSULT-lll
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.
CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
Is malfunctioning part detected?
YES
>> Refer to
SRC-263, "Diagnosis Procedure"
NO
>> INSPECTION END.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1131
SIDE MODULE RH
[GND-SHORT]
Front RH side air bag module circuit is
shorted to ground
• Disconnection of wiring harness and
short
• Internal breakdown in front RH side
air bag module
• Internal breakdown in air bag diag-
nosis sensor unit
B1131 SIDE MODULE RH
SRC-263
< DTC/CIRCUIT DIAGNOSIS >
[FOR MEXICO]
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
2.
CHECK AIR BAG WARNING LAMP
Check the air bag warning lamp status.
Is malfunctioning part detected?
YES
>> Refer to warning lamp flash code chart.
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000005513816
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace wiring harness.
3.
CHECK FRONT SIDE AIR BAG MODULE
1.
Replace front RH side air bag module.
2.
Check the screen of CONSULT-lll.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Check the intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
SRC-264
< DTC/CIRCUIT DIAGNOSIS >
[FOR MEXICO]
B1132 SIDE MODULE RH
B1132 SIDE MODULE RH
Description
INFOID:0000000005513817
DTC B1132 [SHORT] SIDE MODULE RH
For front RH side air bag module, crash is judged by main “G” sensor output signal (left side:LH satellite sen-
sor, right side:RH satellite sensor) and Safing algorithm (in air bag diagnosis sensor unit).
OPERATION
In the case of a collision whose acceleration exceeds the specified level, the ignition materials are ignited by
electric ignition system. The system burns and introduces the chemical reaction of gas generating materials to
generate hot gases that flow into the air bag through a filter and expand the bag.
STRUCTURE
Front RH side air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION
Front RH side air bag module is installed on the side of front seatback with fixed nuts.
DTC Logic
INFOID:0000000005513818
DTC DETECTION LOGIC
With CONSULT-lll
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.
CHECK SELF-DIAG RESULT
Check the screen of CONSULT-lll.
Is malfunctioning part detected?
YES
>> Refer to
SRC-265, "Diagnosis Procedure"
NO
>> INSPECTION END.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.
INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1132
SIDE MODULE RH
[SHORT]
Front RH side air bag module circuit are
shorted to each other
• Disconnection of wiring harness and
short
• Internal breakdown in front RH side
air bag module
• Internal breakdown in air bag diag-
nosis sensor unit
B1132 SIDE MODULE RH
SRC-265
< DTC/CIRCUIT DIAGNOSIS >
[FOR MEXICO]
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
2.
CHECK AIR BAG WARNING LAMP
Check the air bag warning lamp status.
Is malfunctioning part detected?
YES
>> Refer to warning lamp flash code chart.
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000005513819
With CONSULT-lll
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace wiring harness.
3.
CHECK FRONT SIDE AIR BAG MODULE
1.
Replace front RH side air bag module.
2.
Check the screen of CONSULT-lll.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Check the intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст