Nissan Sentra. Instruction — part 57
AV-220
< PRECAUTION >
[NAVIGATION WITHOUT BOSE]
PRECAUTIONS
• Do not perform bypass wire connections for the repair parts. (The
spliced wire will become separated and the characteristics of
twisted line will be lost.)
Precaution for Work
INFOID:0000000009758930
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
PKIA0307E
AV
PREPARATION
AV-221
< PREPARATION >
[NAVIGATION WITHOUT BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009758931
The actual shape of the tools may differ from those illustrated here.
Commercial Service Tools
INFOID:0000000009758932
Tool number
(TechMate No.)
Tool name
Description
—
(J-46534)
Trim Tool Set
Removing trim components
AWJIA0483ZZ
Tool name
Description
Power tool
Loosening nuts, screws and bolts
PIIB1407E
AV-222
< SYSTEM DESCRIPTION >
[NAVIGATION WITHOUT BOSE]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000009758933
Component Description
INFOID:0000000009758934
1. Front tweeter LH
2. GPS antenna
3. Steering switches
4. AV control unit
5. Front tweeter RH
6. Microphone
7. Front door speaker LH
8. Front door speaker RH
9. Rear speaker RH
10. Rear speaker LH
11. Antenna amp.
12. Satellite antenna
13. Rear view camera
14. Window antenna
15. USB interface
16. AUX jack
AWNIA2829ZZ
AV
COMPONENT PARTS
AV-223
< SYSTEM DESCRIPTION >
[NAVIGATION WITHOUT BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Part name
Description
AV control unit
• Operation of navigation and audio systems are integrated.
• Includes the audio, hands-free phone, navigation, satellite radio, rear view
monitor, USB connection and AUX IN connection functions.
• Map data can be loaded from SD-card inserted in SD-card slot.
• Audio signals are output to each speaker.
• Inputs illumination signals required for display dimming control.
• Inputs signals for driving status recognition (vehicle speed and reverse).
• Touch panel functions can be operated by touching display directly.
Map SD-card
A collection of Map data.
AUX jack
AUX sound and data input signals are transmitted to AV control unit.
Front door speakers
Outputs high, mid and low range audio signals from AV control unit.
Front tweeters
Rear speakers
Steering switches
• Operations for audio, hands-free phone and voice recognition are possible.
• Steering switch signal is output to AV control unit.
Microphone
• Used for hands-free phone operations.
• Microphone signal is transmitted to AV control unit.
• Power is supplied from AV control unit.
USB interface
USB sound and data input signals are transmitted to AV control unit.
Rear view camera
• Outputs image of vehicle rear to AV control unit.
• Power is supplied from AV control unit.
Satellite antenna
Satellite radio signal is received and transmitted to AV control unit.
GPS antenna
GPS signal is received and transmitted to AV control unit.
Antenna amp.
• AM/FM signal received by window antenna is amplified and transmitted to AV
control unit.
• Power is supplied from AV control unit.
Window antenna
AM/FM signal is received and transmitted to antenna amp.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст