Nissan Sentra. Instruction — part 906
TM-260
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
KEY INTERLOCK CABLE
KEY INTERLOCK CABLE
Exploded View
INFOID:0000000009759505
Removal and Installation
INFOID:0000000009759506
REMOVAL
CAUTION:
Always apply the parking brake before performing removal and installation.
1. Remove the steering column cover, and the instrument lower panel LH. Refer to
.
2. Remove the center console assembly. Refer to
IP-17, "Removal and Installation"
3. Press the pawls (B) of the key interlock cable slider (A) while
sliding it in the direction of the casing cap (C), and separate the
adjusting holder (D) and slider.
4. Remove the key interlock cable from the shift selector.
1.
Shift selector assembly
2.
Clip
3.
Key interlock cable
4.
Clip
5.
Key cylinder
JSDIA3613ZZ
(E)
:Key interlock rod
JSDIA1797ZZ
KEY INTERLOCK CABLE
TM-261
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
5. Lift the clip (A) in the direction of the arrow (
[C]) and remove
in the direction of the arrow (
[D]).
6. Remove the key interlock cable from the key cylinder.
7. Disengage the clip and disconnect the key interlock cable from
the vehicle.
INSTALLATION
1. Move the shift selector to P position.
2. Turn the ignition switch to ACC or ON position.
3. Install the holder of key interlock cable to key cylinder.
4. Install the clip (A) in the direction of the arrow (
[C]) and push it
in the direction of the arrow (
[D]).
5. Turn the ignition switch to LOCK position.
6. Install the adjusting holder (A) onto the key interlock rod (B),
then install the casing cap (C) onto the shift selector cable
bracket (D).
CAUTION:
• When installing the key interlock cable, never bend or
twist the cable forcefully.
• After connecting the key interlock cable to the shift selec-
tor cable bracket, be sure to check that the casing cap is
completely fastened to the cable bracket. If the casing cap
is easily displaced, replace the key interlock cable.
(1)
: Key interlock cable
(B)
: Key cylinder
JSDIA1798ZZ
(1)
: Key interlock cable
(B)
: Key cylinder
JSDIA3589ZZ
JSDIA1799ZZ
TM-262
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
KEY INTERLOCK CABLE
7. While pressing the detent rod (B) down, slide the key interlock
cable slider (A) toward the key interlock rod (D) side and install
the adjusting holder (C) and key interlock rod.
CAUTION:
• Do not squeeze the pawls on the key interlock cable slider
when holding the slider.
• Do not apply force in a perpendicular direction to the key
interlock rod when sliding the slider.
8. Install the center console assembly. Refer to
9. Install the steering column cover, and the instrument lower panel
LH. Refer to
IP-21, "Removal and Installation"
.
Inspection
INFOID:0000000009759507
INSPECTION AFTER INSTALLATION
• Check the CVT position. If a malfunction is found, adjust the CVT position. Refer to
• The key can be removed only when the shift selector is in the “P” position. (With key interlock)
• It must not be possible to turn the ignition switch to LOCK when the selector lever is not in the “P” position.
(With key interlock)
JSDIA1800ZZ
TCM
TM-263
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
TCM
Exploded View
INFOID:0000000009759508
Removal and Installation
INFOID:0000000009759509
CAUTION:
• When replacing TCM, note the “CVTF DETERIORATION DATE” value displayed on CONSULT “CON-
FORM CVTF DETERIORTN” in MAINTENANCE BOOKLET, before start the operation.
• Do not impact the TCM when removing or installing TCM.
• Before replacing TCM, perform "ADDITIONAL SERVICE WHEN TCM". Refer to
.
• Before replacing TCM and transaxle assembly as a set, perform "ADDITIONAL SERVICE WHEN
REPLACING TCM AND TRANSAXLE ASSEMBLY". Refer to
.
NOTE:
When replacing TCM and transaxle assembly as a set, replace transaxle assembly first and then replace
REMOVAL
1. Remove the battery. Refer to
PG-50, "Removal and Installation (Battery)"
.
2. Remove the air cleaner case assembly. Refer to
EM-25, "Removal and Installation"
.
3. Disconnect the TCM harness connector.
4. Remove the TCM.
5. Remove the bracket.
INSTALLATION
Installation is the reverse order of removal.
Adjustment
INFOID:0000000009759510
ADJUSTMENT AFTER INSTALLATION
When replaced the TCM, perform “ADDITIONAL SERVICE WHEN REPLACING TCM”. Refer to
Bracket
TCM
: Vehicle front
: N·m (kg-m, in-lb)
JSDIA1776GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст